SECURENET iotega Guia De Instalacion página 2

Connect the barrel jack of the plug-in adapter to the power connector on the back of the
iotega.
Plug the other end of the Ethernet cable into the wireless router. Plug the AC adaptor
into an electrical outlet.
The iotega powers up in the following sequence once connected to AC power:
The integrated keypad numbers illuminate in sequence until the iotega is
l
powered up.
After approximately 40 seconds the Power LED illuminates.
l
The Ethernet Link Speed LED illuminates steady green and the Ethernet Link
l
Activity LED flashes rapidly to indicate that a connection is being made.
After several minutes, depending on network speed, the Remote Connection
l
LED illuminates steady green (or flashing green if installer access window is
enabled), indicating that a connection has been established.
1 2 3 4 5
1. Microphone
2. Siren
3. Remote Connection LED
4. Cellular Signal Strength LED
5. WiFi Signal Strength LED
To continue installation, please confirm that you have selected Go Live on the
Account Summary page. You cannot bring the iotega panel online unless this has been
selected.
For more information on LED indicators, see "Controls and Indicators" in the
iotega installation manual.
Verify communications by reviewing the LED lights on the iotega. Below is the
normal operating status.
Power
On steady (green) when AC power is connected.
Ready to Arm
On steady (green) when partition is in a ready to arm mode. No fire or CO
alarms are present.
Armed
On steady (red) when partition is armed.
Off when partition is disarmed or audible alarm annunciation is off.
Trouble
On steady (amber) when system troubles are present.
290010267R001
6 9
7 8
6. Trouble LED
7. Armed LED
8. Ready to Arm LED
9. Power LED
Wi-Fi® Signal Strength
On steady (green) when strong signal connection.
On steady (amber) when weak signal connection.
On steady (red) when no signal, Off when no Wi-Fi detected.
Cellular Signal Strength
On steady (green) when strong signal connection .
On steady (amber) when weak signal connection.
On steady (red) when no signal or no connection detected.
Remote Connection Status
On steady (green) when Link to remote server is active.
On flashing (red) when link to remote server is active but has failed to
communicate.
Off when link to remote server is not active.
Verify the Online Status of the Panel from the SmartTech dealer portal.
In the left side bar, navigate to the "System" page, ensuring the panel is connected and
powered up.
The "System" page displays the current Online/Offline status of the panel.
Enroll Sensors (Zones) and Peripheral Devices onto the iotega by
navigating to the "Panel Settings" page, then selecting "Add Device".
Devices can be enrolled in two ways, either through Auto Enrollment or by entering the
serial number of the device into the "Add Device by Serial Number" form.
To add by Serial Number Form, select the "Add Device" tool and enter the serial
number of the device in the serial number field. Once a valid serial number has been
entered, additional options specific to the device are displayed.
Rename the Zone by entering the desired zone name into the "Label" field. Select
additional zone or device options as required. Once all options are selected, "Submit"
the form.
To add by Auto Enrollmentselect the "Add Device" tool and turn the Auto Enroll
option ON.
Once Device Auto Enroll is ON, press and hold the device enroll button until the LED
lights steady and then release while the LED is still lit. Continue enrolling zones and
peripheral devices until all devices have been enrolled.
Devices are enrolled directly under the respective panel settings sub-sections (zones,
wireless keys, wire-free keypads, sirens).
Navigate to each sub-section to customize the device / zone names and options as
required.
To complete the installation, Enter the WLAN SSID, encryption type and key
for the site WiFi router. This is done in the Network Configuration section of the Panel
Configuration tab under Panel Settings.
Next, select a permanent location to mount the panel. The surface should be flat,
stable, and free from vibration and shock. The iotega should be placed near a power
outlet.
If cables are to be surface run, remove the two breakaway tabs from the bottom of the
mounting plate. Otherwise, pass the Ethernet and AC cables through the opening in the
back of the mounting plate.
2