General Safety Instructions For Electric Tool - Scheppach KS1200 Traducción De Las Instrucciones Originales De Funcionamiento

General safety instructions for electric
tool
CAUTION: Read all safety regulations and in-
structions.
Any failures made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
The term "electric tool" used in the safety instruc-
tions refers to electric tools operated from the mains
power supply (with a power cable) and to battery op-
erated electric tools (without a power cable).
Workplace
• Keep your work area clean and tidy. Cluttered and
dark working areas are accident-prone.
• Do not operate power tools in explosive atmos-
pheres, where flammable liquids, gases or dust
are present. Power tools generate sparks which
may ignite the dust or fumes.
• Keep children and other persons away while op-
erating a power tool. Distractions can be a reason
for losing control of the tool.
Electrical safety
• Power tool plugs must match the outlet. Do not
modify the plug in any way. Do not use any adapt-
er plugs with grounded devices. Unmodified plugs
and matching outlets will reduce the risk of elec-
tric shock.
• Avoid physical contact with grounded surfaces
such as pipes, radiators, ranges and refrigera-
tors. If your body is grounded the risk of an elec-
tric shock increases.
• Do not expose the power tool to rain or wet condi-
tions. Water that enters a power tool will increase
the risk of electric shock.
• Do not abuse the cord; do not use the cord to carry
or hang up the power tool or to unplug the power
tool from the mains. Keep the power cord away
from heat, oil, sharp edges or the power tool's
moving parts. Damaged or tangled power cords
will increase the risk of electric shock.
• When operating a power tool outdoors, use only
extension cords that are approved for outdoor use.
The use of an extension cord that is adapted for
outdoor use reduces the risk of electric shock.
• If working with the power tool in a damp location
cannot be avoided, use a ground fault circuit inter-
rupter. The use of a ground fault circuit interrupter
reduces the risk of electric shock. Always check
whether the mains voltage complies with the volt-
age specified on the nameplate of the power tool.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Warning! This electric tool generates an electro-
magnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Personal safety
• Stay alert. Watch what you are doing and use com-
mon sense when operating a power tool. Do not
use the power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always wear
safety glasses. Safety equipment such as a dust
mask, non-skid safety shoes, a hard hat or ear
protection depending on the type and use of the
power tool will reduce personal injuries.
• Prevent unintentional starting. Ensure that the
power tool is switched off before connecting it to
the power supply and/or battery, picking it up or
carrying the tool. Carrying power tools with your
finger on the switch or energizing power tools that
have the switch on invite accidents.
• Remove any adjusting tool or wrench before turn-
ing the power tool on. A wrench or a key which has
been left attached to a rotating part may induce
personal injury. Do not overreach. Keep proper
footing and balance at all times. This enables you
to better control the power tool in situations which
cannot be foreseen.
• Dress properly. Do not wear loose clothing or jew-
ellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair may get caught in moving parts.
• If dust extraction and collection units are installed,
make sure that these are connected and properly
used. Using such devices reduces hazards asso-
ciated with dust.
Power tool use and care
• Do not force the power tool. Use the correct power
tool for your application. With the correct power
tool you will do the job better and safer at the spec-
ified power rate.
• Do not use the power tool if it has a defective
switch. A power tool, which cannot be turned on
or off with the switch, is dangerous and must be
repaired.
• Unplug the power cord from the outlet and/or re-
move the battery before making any adjustments
to the tool, changing accessories, or storing the
power tool. Such preventive safety measures pre-
vent starting the tool accidentally.
GB 15