Before Starting The Equipment; Replacing The Power Cable - Prowork PG-EL 2150 Manual De Instrucciones

Anleitung_PG_EL_2150_2450E_SPK7:_
GB

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the suction tube (Fig. 3)
Fit the front suction tube (Fig. 3a / Item 1) and
the rear suction tube (Fig. 3a / Item 2) together.
Secure the connection with two safety screws
(Fig. 3b / Item 10) as shown in Fig. 3c.
Connect the rear suction tube (Fig. 3d / Item 2)
to the housing.
Secure the connection with two Philips screws
(Fig. 3e / Item 10) as shown in Fig. 3f.
5.2 Fitting the debris bag (Fig. 4)
Push the debris bag on to the outlet in the
direction indicated by the arrow (Fig. 4a).
Attach the fastening eyelet to the front suction
tube as shown in Fig. 4b.
Start up the tool only after it is fully assembled.
Always inspect the tool power cord for damage
before starting up. The tool may only be used if the
cord is in flawless condition.
6. Operation
6.1 Sizing the strap (Fig. 1)
Fit the strap (4) to the appliance as shown in Fig. 5.
Size the length of the carrying strap (4) so that the
vacuum tube just clears the ground. The guide rollers
(9) at the bottom end of the suction tube will help you
to maneuver the suction tube on the ground.
6.2 Connecting the tool to the power supply and
switching on (Fig. 6, 7)
The tool can be plugged into any socket-outlet (with
230 V AC) that is equipped with a 10A fuse or higher.
The socket-outlet has to be safeguarded by an earth-
leakage circuit breaker (e.l.c.b.). The operating
current must not exceed 30 mA.
b Insert the tool plug into the power cord coupling
(extension).
b Secure the power cord with the sleeve provided
on the tool as shown.
b To switch on, move the ON/OFF switch (Fig.
7/Pos. 5) to ON (I).
b To switch off, move the ON/OFF switch (Fig.
7/Pos. 5) to OFF (O).
14
23.04.2008 15:35 Uhr Seite 14
6.3 Selecting the mode of operation
6.3.1 Suctioning (Fig. 8)
b Turn the lever (Fig. 8/Item 8) to position A. You
can do this both when the device is at a standstill
and while it is running.
6.3.2 Blowing (Fig. 8)
b Turn the lever (Fig. 8/Item 8) to position B. You
can do this both when the device is at a standstill
and while it is running.
b Channel the air stream forward and walk slowly
to blow foliage or garden refuse into a pile or to
clear out hard-to-reach places.
Important!
b Empty the debris bag before blowing.
Otherwise, the material that has been
vacuumed up could drop out.
6.4 Emptying the debris bag and pre-screen
(Fig. 1)
Empty the debris bag (7) in good time. When the bag
is heavily loaded with material, vacuum power is
considerably reduced. Deposit organic refuse at a
compost site.
b Switch off the tool and pull out the plug.
b Open the zipper on the debris bag (7) and
shake out the material.
b Close the zip on the debris bag (7) again.
6.5 Speed control (Fig. 1a, PG-EL 2450 E only)
The device is fitted with an electronic speed
controller. To use it, turn the speed controller (Fig.
1a/Item 11) to the desired position. Use the device
only with the speed which is actually required and do
not let it run at a speed which is faster than
necessary.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.