Electrical Safety - BLACK&DECKER KS600E Manual De Instrucciones

Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
: The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features:
1. On/off switch
2. Lock-on button
3. Dust extraction outlet
4. Shoe plate
5. Saw blade support roller
Fig. E
6. Saw blade storage compartment (KS602E & KS603E)
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped. Used saw blades may be hot.
Adjusting the saw blade support roller (fig. A & B)
Loosen the two screws (8).
u
Push the blade support roller (5) forward until it touches
u
the back edge of the saw blade (7).
Tighten the two screws (8).
u
Fitting and removing the saw blade (fig. C)
Before fitting or removing the saw blade (7) the saw blade
u
support roller (5) must be adjusted to the rear position so
that it does not contact the blade.
Loosen (do not remove) the two screws (10).
u
Hold the saw blade (7) with the teeth facing forward.
u
Insert the shank of the saw blade (7) into the blade holder
u
(9) as far as it will go.
Slightly tighten the two screws (10) alternately to position
u
the blade, then fully tighten the two screws (10).
Adjust the saw blade support roller (5) as described above.
u
To remove the saw blade (7), turn both screws (10) one
u
turn counter-clockwise.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor (11) is required to connect a vacuum cleaner or
dust extractor to the tool. The adaptor can be purchased from
your local Black & Decker retailer.
Push the adaptor (11) into the dust extraction outlet (3).
u
Connect the vacuum cleaner hose (12) to the adaptor (11).
u
Saw blade storage (KS602E & KS603E only) (fig. E)
Saw blades (7) can be stored in the storage compartment (6)
located on the side of the tool
Open the cover of the saw blade storage compartment (6)
u
by holding the tab on the top of the door and pulling outwards.
Remove or store saw blades (7) in the storage
u
compartment (6).
Close the cover of the saw blade storage compartment (6)
u
and make sure that it is latched closed.
Cut line blower (fig. F)
To aid visibility when cutting, your jigsaw is equipped with
u
a cut line blower (13) which will keep the work area clear
of dust as you saw.
Use
Adjusting the shoe plate for bevel cuts (fig. G)
The shoe plate can be set to make either a straight cut or a
left or right bevel cut at an angle of 45°.
Loosen the screws (8).
u
Pull the shoe plate (4) forward, rotate the shoe plate (4) to
u
the left or right and push it back into the 45° location.
Push the blade support roller (5) forward until it touches
u
the saw blade (7).
Tighten the screws (8).
u
To reset the shoe plate for straight cuts:
Loosen the screws (8).
u
Pull the shoe plate (4) forward, rotate to the centre and
u
push it back into the 0° location.
Push the blade support roller (5) forward until it touches
u
the saw blade (7).
ENGLISH
7