tau DOORRAD2 Manual De Usuario página 3

English COMPLIED STANDARDS
DOORRAD2
User Manual (Original)
EC type examination 44 205
1. DESCRIPTION
Cover
Depth Adjustment
Lever Arm
(Outer 2 Rows)
Potentiometer
Dip Switch Y
(Sensitivity Volume)
Connector Dip Switch X
Depth Adjustment
Lever Arm
(Inner 3 Rows)
Indicator LED Area Mask
Area Mask
(Red, Green & Blue) (Inner 3 Rows) (Outer 2 Rows)
Detection Window
4. MOUNTING PRECAUTIONS
Mounting height Mount within 50mm Ensure there are no
is 3m (9.84ft) or from the bottom of the moving objects in the
lower. door engine cover. detection zone.
3.0m
Max 50mm
(9.84ft)
If the sensor is exposed If possible ensure no Ensure the minimum of
to excessive rain install accumulation of snow or reflected sunlight from
with a weather cover. water on the floor. the floor.
To maximize the effectiveness of doorway detection, install the DOORRAD2 outside and inside as shown below.
A B
Side View Plan View
A
Moving Door Leaf
B
6. MOUNTING & WIRING INFORMATION
WARNING
!
Drilling may cause electric shock.
Be careful of hidden wires inside the door engine cover.
1 Attach the mounting template wi th i t s bot tom parallel 2 Drill holes for mounting (3.5mm Ø) and wir-
to the same position as the bottom edge of the door engine ing (10mm Ø) holes.
cover.
50mm
50mm
5 -1 Wiring to a door controller that can test the sensor.
Red
AC/DC
12 to 24 [V]
Sensor' s Black
Cable ±10%
Cable
White N.O.
Note EN16005 Green
COM
Yellow(+) Collector
Set "Test input" dip switch
Blue(-) Emitter
setting Y 6 to "ON"
Ref section 7, Dip Switch OFF
Gray(+)
Test-P
Settings.
Y
Brown(-)
Test-N
ON
6
6 House connectors in the receptacle. 7 Replace Cover.
Disregarding this
WARNING
! !
DIN18650-1:2005
symbol may result in
serious injury or death.
EN 12978:2003
EN 16005:2012
Special attention is required
EN16005
Note
when this symbol is shown.
12 414283-001
2. DIMENSIONS
75mm(2.95") = Standard Mounting Pitch
25mm 15mm 35mm 10mm
(0.98") (0.59") (1.37") (0.39")
Accessories
Mounting Template
230mm(9.06")
Installation
3. LED INDICATORS
Instruction
Green Standby.
Doorway Learning (When dip switch Y 5 is ON).
Green blinking
Blue ROW 4,5 Detecting.
Cable
Red ROW 1,2,3 Detecting.
Orange Detection row "ROW1"("ROW2" when doorway
Base Learning is turned ON) is detecting door movement.
Orange blinking (Fast) Indicates a change of dip switch settings.
Mounting Screws
Door Hold is turned Open (When dip switch Y 4 is Open).
Orange blinking (Slow)
(2 pcs.)
Green/Red blinking (Fast) Internal Sensor Error.
Green/Red blinking (Slow) Reflected infrared signal from the floor is very low.
5. TECHNICAL SPECIFICATIONS
Model Name DOORRAD2
Ensure no condensation
Detection Method Active Infrared Reflection
gets onto the sensor.
Installation Height 3.0[m] (9.84 [ft]) Max
Supply Voltage AC/DC 12 to 24 [V] ±10% 50/60Hz
AC12V-2.1 [VA] (Max)
Power Consumption
DC12V-110 [mA] (Max)
Output Holding Time Approx. 0.5s
Response Time 0.1s ~ 0.2s
Outer 2 Rows 1 [seconds]
Use different frequency Presence Timer
Inner 3 Rows 2s,30s,60s
settings for sensors in
Open collector: 7.5 [mA] (Max) Resistor Load
close proximity.
Opto coupler (NPN)
A B ROW 1,2
Output Voltage: 55 [VDC] Max. Current : 50 [mA] Max.
Dark Current: 100 [nA] Max. (Resistance load)
ROW 2,3,4,5 Form A Relay DC50 [V] 0.1[A] Resistor Load
Test Input 6 [mA] Max. @ 24 [VDC]
Operating Temperature -20 to +60 [Deg.C],(-4 to 140 Deg.F)
Operating humidity Below 80%
IP Rate IP54 (With Base)
Category 2 , performance level D according to EN ISO 13849-1:2008
Weight 0.55 [lb.] (0.25 [kg])
Color Black, Silver
Cable, Mounting Screw 2pcs.,
Moving Door Leaf Accessories
Mounting Template, Installation Instruction
Notice: Specification may be changed without prior notice.
3 If you need to remove the sensor body from its base then
lift the sensor body from the base and tilt it forward to remove
as illustrated.
1
1
2
5 -2 Wiring to a door controller that cannot test the sensor.
Red
Power
(Non Pole)
Sensor' s Black
Cable
Cable
R2,3,4,5 White
Output
Green
Note
Yellow(+)
R1,2
Set "Test input" dip switch
Output
Blue(-)
setting Y 6 to "OFF"
OFF
Ref section 7, Dip Switch Gray(+)
Test Input
Settings.
Y
Brown(-)
ON
6
! WARNING
Be careful not to inadvertently move the Depth Adjustment
Depth Adjustm
Lever Arms when replacing the cover.
ent Lever Arm
7. DIP SWITCH SETTINGS
Disregarding this symbol may
CAUTION
result in injury or damage to
equipment.
Setting required to conform with CAUTION
!
Is advisable to turn off and on again the radar
EN16005.
after each adjustment of the DIP switches.
!
ATTENTION! Every time you change a DIP SWITCH, make sure to turn the power off the radar.
= Default Setting
Function Dip Switch X
Presence
30s
Timer
1 2
44mm
(1.73")
Quantity of
R5
Detection
Rows 3 4
A
Frequency
1 2
Safety
N.O.
Relay
3
Output
Reflection Normal
Diagnostics
4
Function Dip Switch Y
AC24V-2.1 [VA] (Max)
Direction OFF
DC24V-60 [mA] (Max)
Detection
1
Activation
N.O.
Relay
Output 2
Monitor Normal
Mode
3
Auto
Door Hold
4
Doorway
OFF
Learn
5
8. DETECTION AREA WIDTH AND DEPTH ADJUSTMENT
Detection Area Depth Adjustment: Inner 3 Rows
Inner 3
4 Attach the sensor with the mounting rows
adjustment
screws provided.
lever arm
0.5
1.5 1.0 [m]
0
[0 degree] setting
1.0
Door
2.0
2.2
Power
AC/DC
12 to 24 [V] 3.0
(Non Pole)
±10%
N.O. R2,3,4,5
1.0 [m] 0.5 1.0
0
Output
COM
[0 degree] setting
Collector
R1,2
Output
Emitter
1.0
do not connect
do not connect
Door
2.0
2.2
3.0
CAUTION
!
The above illustrated detection areas represent the actual position of the infrared beams. The actual detection area observed will vary depending on the sensor
installation environment, object been detected and sensor settings. Please ensure that the detection area is set to conform to EN16005.
1 2 3 4 1 2 3 4
Dip Switch X Dip Switch Y
Description
The sensor will detect a stationary object for the period of the preset
presence timer setting on the inner 3 rows.
To comply with EN16005 set the presence timer to 30s
EN16005
or more.
The number of rows of detection can be set to 5, 4, 3, 2 depending on
detection area requirements.
When more than two sensors are installed in close proximity to each
other select different frequency settings for each sensor to prevent
cross interference.
Refer to [11.Timing Chart of events] for full details on Safety Output.
A low reflected infrared signal is indicated by a slow flashing Red/Green
LED.
To ignore this low reflection error, set this dip switch to "Low
Reflection"(ON).
EN16005 To comply with EN16005 set to "Normal".
Description
When set to ON, pedestrians moving away from the sensor will not be
detected.
For pedestrian safety purposes when "Doorway Learn"
Note is set to ON the 1st and 2nd row of detection will detect
pedestrians regardless of direction of movement.
Refer to [11.Timing Chart of events] for full details on Activation Output.
Set to Snow in instances where false door activations can result from
blowing snow, leaves or rubbish in the door close area.
! CAUTION
Switch to OPEN to hold the door in the open position.
Doorway Learn allows the 1 row of detection to be focused
st
inside the door close area without detecting the door movement.
When Doorway Learn is turned ON, the sensitivity level
Note of the inner row of detection is only at maximum when
the outer rows of detection are activated.
Detection Area Width Adjustment
Area Mask Area Mask
(Inner 3 Rows) (Outer 2 Rows)
0.5
1.5 1.0 [m]
0
With
[-8 degree] setting Base
1.0
Width
Door
2.0
2.2
Narrow
Wide
3.0 2.0 1.0 0 1.0 2.0
[m] 0.5
0
1.0
[-8 degree] setting
Without
1.0
2.0
Base
Door
2.0
3.0[m]
2.2
Narrow
Wide
3.0
1 2 3 4 5 6
Dip Switch Z
Possible Setting Options
2s 30s 60s ∞
1 2 1 2 1 2 1 2
5 Rows ON 3 Rows ON 2 Rows ON
4 Rows ON
R5 R4 R3 R2
3 4 3 4 3 4 3 4
A B C D
1 2 1 2 1 2 1 2
N.O. N.O.
Safety Output (Opto-Coupler)
N.C. N.C.
7
Transmitter Receiver Transmitter Receiver
Normal Low Ref.
LED
8 8
IR Spot IR Spot
Possible Setting Options
OFF ON
1 1
N.O.
Activation Output (Mechanical Relay)
N.C.
2
Normal Snow
3 3
Auto Open
4 4
Door Door
OFF ON
5 5
Detection Area Depth Adjustment: Outer 2 Rows
Outer 2 rows
adjustment
lever arm
[m]
3.0 2.0 1.0 2.0 1.0 [m]
0
With
[+10 degree] setting [0 degree] setting
Base
1.0
2.0
2.2
3.0
2.0 1.0 [m] 2.0 1.0 [m]
0
[+10 degree] setting [0 degree] setting
Without
1.0
Base
2.0
2.2
3.0
0
1.0
2.0
2.2
3.0
0
1.0
2.0
2.2
3.0