Commencing Operation; Power Supply; General - Medel 95157 Instrucciones Para El Uso

loped, and in the manner described in the instructions for use. Any improper
use can be dangerous.
– In case of prolonged intensive use (e.g. milling of dead skin from your feet) the
device might get very hot. In order to prevent skin burns in these situations,
there should be longer breaks between each application. For your own safety,
constantly monitor heat build up in the device. This particularly applies to peo-
ple who are insensitive to heat.
– The device is only for private use and is not intended for medical or commer-
cial purposes.
– The manager is not responsible for damage or injury caused by improper or
incorrect use.
– The appliance must be checked frequently for signs of wear or damage. If
such signs are present, or if the appliance has been used improperly, it must
be taken to either the manufacturer or the dealer before further use.
– Switch off the instrument immediately in the event of defects or malfunctions.
– Repairs may be carried out only by the customer service or authorized dealers.
– On no account try to repair the instrument yourself!
– Use the instrument only with the accessories provided.
– Never leave the instrument unattended when it is in operation.
– Keep the instrument away from children to prevent any possible danger.
– Keep the instrument away from sources of heat.
– Do not use the instrument under blankets, pillows etc.
– The instrument must not be operated continuously for longer than 15 minutes.
After this time, wait an interval of at least 30 minutes to prevent the motor from
overheating.
– Do not use the instrument when bathing or showering. Do not store or keep
the instrument in places from where it could fall into a bath or wash basin.
– Never immerse the instrument in water or other liquids.
– If the instrument has dropped into water, unplug the plug-in power unit imme-
diately.
– Ensure your hands are dry before handling either the instrument or the plug-in
power unit.
– Do not pull on the power cord or instrument to unplug the plug-in power unit
from the socket outlet.
– The plug-in power unit must be operated only from a power supply as speci-
fied on it.
– If the power supply is damaged, don't use the adaptor anymore!
– For reasons of hygiene, the device should only be used on one person.
100127_MEDEL BD MANICURE PEDICURE EXPERT 95157_REV.01_05.06.17.indd 12-13
12

2. Commencing operation

2.1 Information concerning the instrument
This manicure and pedicure device comes with high-quality attachments. The
supplied 6 attachments are made with durable sapphire coating / polishing felt.
Together with the continuously adjustable speed regulation and right/left rotati-
on, professional foot and nail care at the standard of a pedicurist is possible.
All the attachments can be easily integrated into the storage pouch of the
MANICURE/PEDICURE EXPERT.
The integrated LED light additionally creates ideal light conditions during appli-
cation.

2.2 Power supply

To ensure adequate power at all times for good and powerful treatment of the
feet and nails, this instrument is provided with a permanently attached power
unit.
After use, before cleaning and changing any accessory parts, the po-
wer unit should always be disconnected.
Ensure that the sliding switch on the device is in the centre position (=
off) before you connect the device to a power supply.
3. Application

3.1 General

– This instrument is intended only for the treatment of hands (manicure) and feet
(pedicure).
– Make sure that the device is switched off beforehand.
– Select an attachment and push it onto the instrument spindle using a slight
pressure. The attachments can be heard to engage. To remove: pull the at-
tachment and instrument apart in the axial direction (straight).
– Turn the control ring to the left (anti-clockwise rotation) or to the right (clock-
wise rotation) to switch the device on. The LED lights up blue. The two buttons
marked with plus (+) and minus (-) allow you to select the speed of rotation.
Start every application at low speed and increase it only as required.
– All file and cutting attachments are coated with a sapphire grain. This guaran-
tees extremely long life and almost guarantees freedom from wear.
– Do not exert heavy pressure and always guide the attachments carefully over
the surface to be treated.
– Move the instrument under light pressure in circular movements slowly over
the parts to be treated.
– Note that the cutting attachments will have a reduced effect if the skin is sof-
tened or moist. For this reason, do not carry out any pretreatment in a bath.
13
05/06/2017 12:40:21