Troubleshooting; Service Information - Black and Decker RapidRoller BDPR400 Manual De Instrucciones

Recommended accessories for use with your
If you need assistance regarding accessories, please call: 1-800-544-6986
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Fill tube can clip - for use with containers which do not fit the round can cover provided. Available through a
Black & Decker Service Center.
When using larger containers such as a five gallon bucket, use the fill tube can clip with a length of 3/4 inch
I.D. tubing available at most large home centers. The tubing fits over the ribbed end of the fill tube.
Perforated roller sleeves are available at hardware stores.
PROBLEM
Takes a long time for paint to appear on surface.
Air is drawn into handle instead of paint.
Difficult to insert or remove fill tube from valve.
Handle is difficult to move in and out.
Paint leaks out end cap.
Paint leaks out of fill valve.
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or
call the BLACK & DECKER help line at 1-800-544-6986.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool
service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or
visit www.blackanddecker.com
Warranty
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product
will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the
store is a participating retailer). Returns should be made within the time period of the retailerʼs policy for exchanges (usually 30 to 90
days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns
that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or
replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed
under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary
from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker
Service Center. This product is not intended for commercial use.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country
specific warranty information contained in the packaging, call the local company or see the website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free
replacement.
Black & Decker (U.S.) Inc.,
Towson, MD 21286 U.S.A.
Accessories
R R
APID OLLER

Troubleshooting

Imported by
701 E. Joppa Rd.
are available from your local dealer or authorized service center.
TM
SOLUTION
See first note on "Painting with the R
second fill.
Slowly push handle in to expel air. Remove and reinsert product on
fill tube. Be sure fill tube is fully seated in valve body. If necessary,
apply petroleum jelly to fill tube which makes it easier to seat fill tube
and valve body.
Make sure O-ring is in place between handle assembly and roller
frame and well lubricated.
Put petroleum jelly in fill port opening and or fill tube.
Lubricate rubber seals at end of plunger, or twist plunger slightly to
break seal.
Make sure both end caps are pushed snugly into and are even with
the end of roller cover. If they are OK, remove end caps, clean out
any old paint and relubricate with petroleum jelly.
Lubricate valve with petroleum jelly.
Make sure wiper seal is in place.
7
R ". May take a
TM
APID OLLER
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales