ALPHA-TOOLS TS 125/115 Manual De Instrucciones página 9

Anleitung TS 125 SPK7 17.09.2004
1. Layout (Fig. 1)
1. Spark protection
2. Base plate
3. Fastening material for angle grinder
4. Clamping device for workpiece
5. Swing arm
6. Handle
7. Cable holder
8. Holder for angle grinder
9. Adjusting screws for angle grinder
Important: There is no angle grinder supplied with
the cutting stand!
2. Safety information
Important! The following basic safety actions
must be taken when using accessory devices
with our electric tools in order to protect the user
from electric shocks, risk of injury and other
trouble. Read and follow these instructions
before using the device and keep this manual in
a safe place.
1. For your own safety, read and observe this safety
information for the cutting stand as well as the
safety instructions issued by the manufacturers of
the electric tool and cutting-off wheel with regard
to cutting.
2. The cutting stand must always be securely
fastened to a workbench in a horizontal position.
3. Keep your workplace clean and well illuminated.
4. Avoid abnormal working postures. Make sure you
stand squarely and keep your balance at all
times.
5. Never use the machine in the vicinity of
combustible materials, liquids or gases.
6. Wear safety goggles, a visor, a breathing mask,
an apron, safety shoes, long tight sleeves and
gloves.
7. Keep children away. Do not allow other persons,
particularly children, to touch the tool. Keep them
out of your work area.
8. Never work without a guard over the cutting-off
wheel or without standard spark protection.
9. Always leave the safety devices in position and
make sure that they are in good working order.
10.Always check the cutting-off wheel for cracks or
signs of damage. Replace cracked or damaged
cutting-off wheels immediately.
11.Before operation, make sure that the cutting-off
wheel does not touch the machine.
9:07 Uhr Seite 9
12.Check in regular intervals that all screws, nuts
and bolts are fastened securely enough.
13.Make sure that the power cable is a safe distance
from the cutting-off wheel and the working area.
14.Do not use the cutting stand with high-
performance electric tools that are not suitable for
the accessory device.
15.Use only cutting-off wheels for metal.
16.Make sure that the cutting-off wheel moves
vertically to the base plate.
17.Secure the workpiece carefully. It has to be
securely clamped in a straight position in order to
prevent it from moving and skewing while the cut
is being made.
18.Do not try to cut workpieces which are obviously
too big for the cutting stand.
19.Make sure that the cutting-off wheel stops
completely before you remove the workpiece,
clamp in a new workpiece, or adjust the angle.
20.Never reach behind or near the cutting-off wheel.
21.Never leave an electric tool unattended when it is
running. Always switch off your electric tool
before leaving it.
22.Always pull out the power plug when not in use,
before carrying out any maintenance work and
before changing the tool.
23.Avoid unintentional starting. Make sure that the
switch is OFF when inserting the plug in the
socket-outlet.
24.Never use circular saw blade or ceramic wheels.
25.Before using, make sure that the device is
securely fastened in accordance with the
instructions.
26.Never use your hands or any other objects to
stop the wheel.
27.Do not overload your tool; allow the wheel to
work without applying any pressure.
28.Check to see if all parts are mounted. In this
connection, please read the instructions and
particularly the safety information. Only use a
fully mounted machine.
29.Use the accessory parts and electric tools for
their intended purpose only.
30.Check to see if the accessory parts are not
damaged. Also make sure the moving parts of
the clamping device and safety guard are working
correctly.
31.Be alert at all times. Concentrate on what you are
doing. Use common sense. Never use the
electric tool when you are distracted.
32.The cutting stand is designed for cutting ferrous
metals. Do not try to cut wood, brick or other
unsuitable materials.
33.Do not stand in the cutting direction after a new
GB
9