Metra 95-7309 Instrucciones De Instalación

Hyundai 1995-2006
Ocultar thumbs Ver también para 95-7309:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hyundai 1995-2006
KIT FEATURES
• ISO DDIN radio provision
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) Spacers, thick and thin • D) (4) #10 x 3/4" Phillips screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7300 • 70-7301 • 70-2003 (Santa Fe with a Monsoon amp)
Antenna Adapter: • 40-GM 10 (Santa Fe with a Monsoon amp)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
METRA. The World's best kits.
Installation instructions for part 95-7309
95-7309
C
thick
thin
metraonline.com
Dash Disassembly
– Hyundai Elantra (with double DIN radio)
– Hyundai Santa Fe 2001-2006 ............................... 2
– Hyundai Sonata 1995-2001 ................................. 3
– Hyundai Tiburon (with double DIN radio)
Kit Assembly
– ISO DDIN radio provision ...................................... 4
D
– Legend................................................................. 4
CAUTION!
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
Table of Contents
1996-2000 .......................................................... 2
1997-2001 .......................................................... 3
Metra recommends disconnecting the negative bat -
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Metra 95-7309

  • Página 1 • A) Radio housing • B) Radio brackets • C) Spacers, thick and thin • D) (4) #10 x 3/4” Phillips screws – ISO DDIN radio provision ........4 – Legend..............4 CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle thick thin manufacturer recommends against so.
  • Página 2: Dash Disassembly

    95-7309 Dash Disassembly Santa Fe 2001-2006 Elantra (with double DIN radio) 1996-2000 1. Remove the ashtray, and then remove (2) Phillips screws now 1. Unclip and remove the dimmer exposed in the cavity. (Figure A) switch panel, and then remove (1) Phillips screw exposed behind the 2.
  • Página 3 95-7309 Dash Disassembly Sonata 1995-1998 Tiburon (with double DIN radio) 1997-2001 1. Unclip and remove the trim panel around the shifter. (Figure A) 1. Unclip and remove the panel 2. Remove (1) Phillips screw at the surrounding the shift lever. (Figure A) bottom of the radio trim panel.
  • Página 4: Kit Assembly

    Please have the vehicle apart 3. Locate the factory wiring harness and antenna connector and ready to perform troubleshooting steps in the dash. Metra recommends using the proper mating before calling. adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
  • Página 5: Componentes Del Kit

    Instrucciones de instalación para la pieza 95-7309 Indice Hyundai 1995-2006 95-7309 Desmontaje tablero – Hyundai Elantra (con radio doble DIN) 1996-2000 ............2 – Hyundai Santa Fe 2001-2006 ....... 2 CARACTERÍSTICAS DEL KIT – Hyundai Sonata 1995-2001 ......... 3 • Provisión de radio ISO DDIN –...
  • Página 6: Desmontaje Tablero

    95-7309 Desmontaje tablero Santa Fe 2001-2006 Elantra (con radio doble DIN) 1996-2000 1. Retire el cenicero, y luego retire (2) tornillos Phillips ahora expuestos 1. Soltar y desmontar el panel en la cavidad. (Figura A) regulador de intensidad, y luego retire (1) tornillo Phillips expuestos 2.
  • Página 7 95-7309 Desmontaje tablero Sonata 1995-1998 Tiburon (con radio doble DIN) 1997-2001 1. Suelte y retire el placa de moldura palanca de cambios. (Figura A) 1. Suelte y retire el placa de moldura 2. Retire (1) tornillo Phillips en la parte palanca de cambios.
  • Página 8: Ensamble Del Kit

    Instrucciones de instalación para la pieza 95-7309 Ensamble del kit IMPORTANTE Provisión de radio ISO DDIN Si tiene dificultades con la instalación 1. Coloque el espaciador adecuado (ver leyenda) entre de este producto, llame a nuestra línea el carcasa del radio y los soportes de radio, alineando de soporte técnico al 1-800-253-TECH.

Tabla de contenido