Installation Instructions; Wireless Backup Camera Installation Instructions - Garmin BC 20 Manual De Instrucciones

BC ™ 20 Wireless Backup Camera

Installation Instructions

Wireless Backup Camera Installation
Instructions
See the Important Safety and Product Information guide in the
GPS device product box for product warnings and other
important information.
Garmin strongly recommends having an experienced installer
®
with the proper knowledge of electrical systems install the
device. Incorrectly wiring the power cable can result in damage
to the vehicle or the battery and can cause bodily injury.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place will void the product warranty.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
These installation instructions do not apply to a specific vehicle
type, and are meant as a guide when installing this product on
your vehicle. For questions specific to your vehicle, you should
contact the vehicle manufacturer.
Item Description
Wireless camera PND mount
The PND device must be powered through this mount to
communicate with the camera.
Transmitter
Camera
Camera mounting bracket
Tools Needed
• Drill and 0.36 in. (9.09 mm, or size T) drill bit
• #2 Phillips screwdriver
• Screws, bolts, or cable ties (to secure the transmitter)
• Solderless wire-splice connector or solder and heat-shrink
tubing
• RV sealant (optional)
Camera Mounting Considerations
When selecting a location to mount the camera, observe these
considerations.
• You should test a mounting location before you permanently
mount the camera.
2
WARNING
CAUTION
NOTICE
• Installing the camera higher on the back of the vehicle
provides a better viewing angle.
• The included bracket can be clipped onto a license plate or
other similar surface, or it can be fastened to the back of the
vehicle using the included self-tapping, panhead screws.
Transmitter Location and Wiring Considerations
The transmitter is not intended to be held or worn on your body
while it is in use.
When selecting a location to install the wireless transmitter,
observe these considerations.
• You should test a proposed installation location before you
permanently install the transmitter.
• Some vehicles do not provide constant minimum voltage to
the reverse lamps. You should use an automotive relay when
connecting the transmitter and camera to a power source that
does not provide constant voltage.
• Although the transmitter can transmit the video signal
approximately 10 m (30 ft.), the location of the transmitter can
affect this range.
◦ The closer you install the transmitter to the receiver, the
more reliable the signal.
◦ The signal transmits from the flat front and back surfaces
of the transmitter. The transmitter provides the best
signal when either flat surface points toward the receiver.
◦ Dense metal or appliances
greatly reduce the transmission distance.
◦ The fewer solid objects that exist between the path of the
transmitter and the device, the more reliable the signal.
• If the distance between the camera and the transmitter
exceeds the length of the included cable, additional extension
cables can be used. A 15 m (50 ft.) extension cable can be
purchased, and more than one extension cable can be
installed. See your Garmin dealer or go to
for more information.
• The fuse holder located near the transmitter is not
waterproof. Installing the fuse holder in a location that is
exposed to the elements is not recommended.
• The connector between the camera and the transmitter is not
waterproof. If you make this connection in a location exposed
to the elements, you must make sure that the connection is
waterproof.
• If you are installing the camera on a boat trailer or other
location that may be exposed to water, you must waterproof
all wiring connections and the fuse holder in the transmitter
cable.
Testing the Camera and Transmitter Location
1
Temporarily secure the camera in the preferred mounting
location.
2
Temporarily place the transmitter in the preferred installation
location, and connect it to power and to the camera.
NOTICE
in the path of the transmitter
www.garmin.com
Installation Instructions