Sammic TH-1100 Instrucciones De Uso página 3

OPERATING INSTRUCTIONS
– Read thoroughly and stick closely to the
istructions and warnings.
– Always keep this booklet and pack it
along the appliance
– Before use, ensure that the mains
voltage is the same as the voltage
indicated on the data plate of the
machine.
– Connect the appliance only to 10 Amp
sockets that are efficiently earthed.
ALWAYS REMOVE THE PLUG FROM THE
SOCKET BEFORE CARRYING OUT ANY
MAINTENANCE OR CLEANING OF THE
APPLIANCES.
– Never tamper with the machines anyway.
– For all interventions on the machines,
always apply only to the authorized
centre service.
– Never pull the power cable to remove
the plug from the socket.
– Take care to extend the power cable
before use
– Never leave the machine unguarded
when switched on; keep it out of the
reach of children and incompetent
people.
– Never switch on a machine that seems to
be faulty.
– For repairs and the
accessories, always apply only to the
dealer.
– Remove any protective film before use.
– Only use original accessories and parts.
– Do not use the appliance outside or in
damp environments.
– Do not immerse or bathe the appliances
in water or any other liquid.
– To avoid the danger of fire, never cover
the appliances.
– Unplug the appliance from the mains
when it is not in use.
– Ensure the power cable does not come
into contact with appliance.
– Let the appliances cool down before
moving them.
– Only use the applance for the purposes
it is meant for; any other use is
considered improper and is therefore
dangerous.
– Position the appliance a minimum of 5
cm. from walls so as to allow optimum
aeration and away from sinks and jets of
water.
– Always work under the best possible
safety conditions. Avoid using the
appliance with wet feet or hands or
barefoot.
– In the interests of safety, the appliances
must always be consedered as live.
– To clean the appliances, (which must be
performed only when they have been
unplugged from the mains and have
cooled), use a well-wrung damp cloth
and specific products to clean stainless
steel/aluminium/paint/chrome on the
body; components that come into
contact with food can be cleaned
separately by hand with water and
washing-up liquid (do not put them in
the dish washer).
– To avoid dragging or scratch on the
body never
detersive with abrasive action.
AS THESE
APPLIANCES, THEIR USE IS RESERVED TO
SPECIALIZED OPERATORS
FOR MACHINES
purchase of AUTOMATIC STOPPING DEVICE IN CASE OF
LOSS OS ELECTRICITY: if there is a loss of
current, the machine (fitted with this
device on request) will switch off and
remain switched off until it is manually
reset as follows:
1) set the switch to 0;
2) wait for approx. a second;
3) reset the switch.
The manufacturer reserves the right to
make alteration to the appliances and to
the accessories supplied without prior
notice.
Type of appliance ICE-BREAKER
Appliance intended for breaking ice into
pieces of 4 different sizes.
Operates by means of the luminous switch
use cloth, sponge or
ARE PROFESSIONAL
FITTED WITH AN
• it has a microswitch which blocks the
motor opening the cover
• the motor operates for about 35
minutes after which it is disactivated by
a safety heat sensor; it starts operating
again once it has cooled
• put the ice-cubes into the container only
with closed regulation system (pos. I )
• switch-off, open the cover, empty the
container and clear the clogged outlet
for ice if, in exceptional circumstances,
an ice-cube has got stuk between the
slit
• never put your hands or any utensils
into the container
• maximum time required to break up a
whole container of ice 1:-- 1,30 minutes
• never use idling and for long periods
• always wait until the motor stops
completely before opening the cover
• not suitable for continuous use - use for
a maximum of about 20 minutes
• always switch-off at the end of the work
and after every operation
• always remove the plug before carrying
out any maintenance or clearing.
REGULATION SYSTEM:
• Pos.I tiny ice particles
• pos. II finely crushed ice
• pos. III medium-size pieces of ice
• pos.IV large pieces
ATTENTION: moving parts
SPECIFICATIONS
E 230V / 50-60Hz / 1
NERGY SUPPLY
L
OADING
D mm
IMENSIONS
- Width
- Depth
- Height
N
ET WEIGHT
TH-1100
~
450W
25
30
66
9
3
ENGLISH