Remington MB4030 Manual De Instrucciones página 3

ENGLISH
FHOW TO USE
,Before you begin
• Always comb your beard or moustache with a fine comb before you start trimming
,Adjusting the trim length
• The trimmer comb can be adjusted to give you 9 different trim lengths simply by turning
the wheel to the desired setting.
• Turn the wheel clockwise for shorter length, anti-clockwise for longer length.
• The wheel will click into place as it reaches each setting, and the setting number will
appear on the length position indicator.
SETTING HAIR DESCRIPTION
1
Stubble or Cropped look
2
3
Short
4
5
Medium
6
7
8
9
Long
,0.5 – 5.5mm guide comb
The 0.5 – 5.5mm guide comb can be adjusted to give you settings of 0.2mm adjustment
simply by turning the wheel to the desired setting. Turn the wheel clockwise for longer
length and anticlockwise for shorter length.
The setting will appear on the length position indicator.
,Attaching and removing the 0.5 – 5.5mm guide
With the trimmer blade facing away from you, slide the guide comb on top of the trimmer
blade and click into position.
With the trimmer blade facing away from you, carefully push the guide comb away from the
trimmer blade.
4
HAIR LENGTH
1.5mm 0.06''
2.5mm 0.1''
4mm
0.16''
5.5mm 0.22''
7mm
0.28''
9mm
0.35''
11mm
0.43''
14mm
0.55''
18mm
0.71''
comb.
ENGLISH
Note: Trimmer comb must be attached to the product in order to use the hair length
selector.
,To thin and taper beards/ moustaches
• Attach an attachment comb to the 30mm Trimmer Blade.
• Use the zoom wheel to set the trimmer comb to the desired length setting. The setting
will appear on the length position indicator. If you are trimming for the first time start
with the maximum trimming length setting
• Turn the unit on.
• Place the flat top of the trimmer comb against the skin
• Slowly slide the trimmer through the hair. Repeat from different directions as necessary.
• If hair builds up in the trimmer comb during the trimming process, switch the unit off,
pull off the comb and brush/rinse off
,To define the beard/moustache line
• Hold trimmer with 30mm Trimmer Blade facing you.
• Remove the trimmer comb attachment
• Start with edge of beard/moustache line and gently lower the trimmer blade onto your
skin. Use motions towards edge of beard/moustache line to trim to desired locations in
facial area and away from beard in neck area.
• For finer shaping, raise the pop-up trimmer. Shape as desired.
C BLADE RELEASE
• Remove the adjustable comb.
• Push the release button on the back of the product.
• Blade will release itself from its housing.
• Remove the blade from the housing.
• To replace the blade, make sure the blade is aligned and the grooves on the blade
cartridge match up with slots in the housings.
• Push the blade into the housing until it snaps into place.
C REPLACING THE TRIMMER COMB
• Hold the trimmer in one hand with your thumb firmly on the zoom wheel to keep it from
turning. Ensure that the length position indicator is at 1.
• Slide the comb/shaver down the grooves until it clicks into place.
Note: The trimmer comb attachment can only be placed on the trimmer one way; if it
does not fit properly remove and reverse it.
ETips for best results
• Beard, moustache and sideburn hairs should be dry.
• Avoid using lotions before using your trimmer. Comb your hair in the direction that it
grows.
• Remove trimmer comb attachment if you are: defining hairline edges such as sideburns,
trimming the nape of your neck, trimming your beard line on front of neck.
5