EN
7. Cleaning and Maintenance
7.1 Before cleaning the appliance,disconnect it from the socket and let it cool down. The enclosure is easily to
get dirty, wipe it often with soft sponge. For every dirty parts, wipe with a sponge dipped in <50°C water
and mild detergent, then dry the heater enclosure with clean cloth. Be careful not to let the water enter
the appliance inner. Don't splash water onto the heater,never use solvent like gasoline etc. to clean the
heater,in order to protect the enclosure.
7.2 Clean the cord and plug,dry and pack it in a plastic bag.
7.3 When you store the heater, let it cool down first, keep it dry. Then cover it with a plastic bag, put in a
packing box and store it in a dry, ventilated place.
8. Trouble shooting:
You can solve many common problems easily, saving you the cost of a possible service call.
Try the suggestions below to see if you can solve the problem before calling the service centre.
Problem
Possible cause
The heater does not
The plug is loose, bad connection
operate,even when it is
plugged in and the switch,
thermostat are switched on.
No power in socket outlet
The input voltage is too high or
too low
The heating element
glowing
The air inlet grill is blocked
The switch was not put at heating
setting
The thermostat operated
The appliance didn't heat up,
or only ventilator worked
The self-resetting cut-out operated
Abnormal noise
The appliance is not stands upright Put the heater on a level surface
Treatment
Model identifier(s): GP 08 24
Item
Pull out the plug, check the
Heat output
connection of the plug and socket.
Nominal heat output
Then connect again.
Minimum heat output (indicative)
Insert the plug in a proper socket
Maximum continuous heat output
Auxiliary electricity consumption
Use power supply according to
At nominal heat output
the rating on the label
At minimum heat output
In standby mode
Keep the heater far way from
articles like curtain, plastic bag,
paper and other things which can
cover the inlet or can be easily
cover on the air inlet
Turn the switch to heat setting
Turn the thermostat and listen if
there is open/close voice. If there is
no click and the thermostat is not
Contact details:
damaged, the heater will automatic
Remark:
For electric local space heaters, the measured seasonal space heating energy efficiency ηs cannot be worse than the declared value at the nominal
switch on when the appliance
heat output of the unit.
cooled down
Turn the heater off and inspect
the blockage of inlet or outlet.
Disconnect the plug and wait at
least 10 minutes for the protection
system to reset before attempting
to restart the heater.
Symbol
Value
Unit Item
Type of heat input, for electric storage local space heaters only (select one)
Pnom
2.4
kW
Manual heat charge control with integrated thermostat
Manual heat charge control with room and/or outdoor
Pmin
1.2
kW
temperature feedback
Electronic heat charge control with room and/or outdoor
Pmax
2.4
kW
temperature feedback
Fan assisted heat output
elmax
N/A
kW
Type of heat output/room temperature control (select one)
elmin
N/A
kW
Single stage heat output and no room temperature control
elSB
N/A
W
Two or more manual stages, no room temperature control
With mechanic thermostat room temperature control
With electronic room temperature control
Electronic room temperature control plus day timer
Electronic room temperature control plus week timer
Other control options (multiple selections possible)
Room temperature control, with presence detection
Room temperature control, with open window detection
With distance control option
With adaptive start control
With working time limitation
With black bulb sensor
See cover page with contact information
Disposal Environmental Protection
Waste electrical production should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Unit
[no]
[no]
[no]
[no]
[no]
[no]
[yes]
[no]
[no]
[no]
[no]
[no]
[no]
[no]
[no]
[no]