AKG IVM 1 Modo De Empleo página 23

5. To defeat IVA press SELECT. The command >OFF< stops blink-
ing to indicate IVA is switched out of circuit:
IVA OFF
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
6. To switch IVA back in, repeat steps 1 to 3 above, select "IVA:
>ON<", and press SELECT. The display will change to this:
Custom Tight
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
Note: The selected setting will remain in memory even after
powering down. In a multichannel IVM1 system, this
allows you to switch IVA out permanently for any channel
selectively if individual musicians prefer an unprocessed
monitor signal.
Note: If you have selected "IVA OFF", pressing SELECT from any
menu will bring up the display message "IVA OFF" rather
than the main menu. To return to the main menu press
MENU.
7.5.9. Mute
To mute the system completely call up the "Mute" menu:
1. Press MENU.
2. Press or as many times as necessary to call up this
display:
Menu: Mute
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
3. Press SELECT to call up the menu commands:
Mute: >OFF<
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
4. The or toggles between "Mute >OFF<" (normal mode)
and "Mute >ON<" (system muted).
Mute: >ON<
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
5. To activate the desired setting press SELECT. If you selected >
ON< the display will change as follows:
MUTE
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
22
O O
04
O
LOCK
MENU SELECT
O O
04
O
LOCK
MENU SELECT
04
LOCK O
MENU SELECT
O O
04
O
LOCK
MENU SELECT
04
O O
LOCK
MENU SELECT
O O
04
O
LOCK
MENU SELECT
6. To deactivate MUTE repeat steps 1 to 3, select >OFF<, and
press SELECT.
The display will revert to the main menu.
7.5.10. RF Channel
To select the transmission channel (= the number of the desired
carrier frequency) call up the "RF Channel" menu:
1. Press MENU.
2. Press or as many times as necessary to call up this dis-
play:
Menu: RF Channel
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
3. Press SELECT.
4. Press or to select one of the 16 carrier frequencies. The
display will indicate the channel number (blinking) and the se-
lected carrier frequency (e.g., 775.850 >MHz<).
RF: >06< 775.850 >MHz<
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
Note: Channel 16 is followed by the command "RF >OFF<".
This command allows you to switch off the transmission
signal.
5. Press SELECT to save the selected frequency. the message
"busy" will appear in the display while the frequency is being
saved:
RF: busy
8 A c
█ █
EAR SND AMB STEREO RFCH
IVA
As soon as the message "BUSY" has disappeared the display
will revert to the main menu and indicate the currently active
transmission channel above the "RFCH" label.
Note: If you selected >OFF< two lines will appear in the display
above the "RFCH" label:
Custom Tight
8 A c █ >_ _<
█
EAR SND AMB STEREO RFCH
IVA
To switch the transmission signal back on, repeat steps 1
through 5 to activate a transmission channel.
7.5.11. Panorama
The "Panorama" menu allows you to adjust the apparent distance
between the virtual monitors in 5 steps.
1. Press MENU.
2. Press or as many times as necessary to call up this dis-
play:
04
LOCK
O
MENU SELECT
04
O O
LOCK
MENU SELECT
O O
06
O
LOCK
MENU SELECT
O O
O
LOCK
MENU SELECT