Spare Parts; Electrical Diagram; Disposal; Ce Declaration - PLYMOVENT TEV-385 Instrucciones Para El Uso

waRNiNg!
Always switch off the machine and disconnect it
from the mains before carrying out the activities
below. First read the maintenance regulations at the
beginning of this manual.
Symptom problem
Motor does Machine does
not start. not function.
Motor makes Machine does
a humming not function.
sound, but
does not run.
Motor stops Machine does
automatically. not function.
Poor suction. Machine does
not function
properly.
Vibrations in Machine not
the machine. steady.
8

SpaRE paRTS

The following spare parts are available for the product (refer to
the exploded view, Fig. IV on page 39.
article number Description
TEV-385
0000100600 Fan wheel TEV-385
0000100604 Motor TEV-385; 230-400V/3ph/50Hz
TEV-585
0000100601 Fan wheel TEV-585
0000100605 Motor TEV-585; 230-400V/3ph/50Hz
0000100437/010812/0 TEV-RANGE
possible cause Solution
No mains Check the mains
voltage. voltage.
Mains cord Repair or replace
defective. mains cord.
Loose contacts. Repair the
contacts.
Motor protection Replace the
switch defective. motor protection
switch.
Motor defective. Repair or replace
motor.
Motor uses 2 Repair the phase
phases instead of connection.
3 (three-phase
motor only).
Motor capacitor Repair or replace
defective/not the motor
connected (single capacitor.
phase motor
only).
Motor protection Let the machine
switch activated. cool down for
some time.
Check setting of
motor protection
switch (MPS)
according to
electrical
diagram.
Motor defective. Repair or replace
the motor.
Inverted Change the
direction of direction of
rotation of the rotation.
motor (three-
phase motor
only).
Motor defective. Repair or replace
the motor.
Extraction fan Clean the
polluted. extraction fan.
Outside air is Check or replace
being extracted. the sealing
material.
Imbalance in the Clean the
extraction fan. extraction fan.
article number Description
TEV-765
0000100602 Fan wheel TEV-765
0000100606 Motor TEV-765; 230-400V/3ph/50Hz
TEV-985
0000100603 Fan wheel TEV-985
0000100607 Motor TEV-985; 230-400V/3ph/50Hz
9

ELEcTRicaL DiagRaM

Refer to the separately supplied electrical diagram.
10

DiSpOSaL

After life of the product, dispose it of in accordance with
federal, state or local regulations.

cE DEcLaRaTiON

CE declaration of conformity for machinery
We, Plymovent Manufacturing BV, Wezelkoog 11, 1822 BL
Alkmaar, the Netherlands, herewith declare, on our own
responsibility, that the product(s):
- TEV-385
- TEV-585
- TEV-765
- TEV-985
which this declaration refers to, are in accordance with the
conditions of the following Directive:
- Machine Directive 2006/42 EC
- EMC directive 2004/108 EC
- LVD 2006/95/EC
- ErP directive 2009/125/EC
Alkmaar, the Netherlands, 1 December 2012
Ir. F. Coehoorn
Vice President Research & Development
An installation is defined as a combination of several finished
products or components that are assembled by an installer at
a given place. The various parts of the installation are intended
to operate together in a particular environment and to perform
a specific task. The entire installation must comply with the
relevant directives and standards. The assembly instructions
given by the manufacturer, as well as the whole method of
installation, must be in accordance with good engineering
practices within the context of installations, as well as
installation rules. Considering the above, the installer will be
responsible for completing the installation and issuing the final
CE Declaration of Conformity.
EN - 7