ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Spotlight for Pool, model AR-20660, follow the instructions indicated below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
Elevated Swimming Pool Floodlamp: AR-20660 (75W)
Elevated Swimming Pool Floodlamp Unit + Floodlamp Arm Support Unit (Both units are supplied mounted)
•
Transformer with cable
•
4 Lenses (blue, green, red and yellow)
•
Bag with Beach Fastening
•
Hook bracket
•
Installation and maintenance manual
•
2. GENERAL CHARACTERISTICS
This floodlamp has been designed for use primarily in Elevated Swimming Pools. It is a Class III electric apparatus with very low
safety voltage (12 V with alternating current).
To begin operation of the Floodlamp, it must be fully submerged in the water.
The floodlamp complies with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a nominal
immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS PART 2:
SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric
components which have been inserted or handled at locations other than its own premises.
3. INSTALLATION
•
The floodlamp is mounted vertically on the pool wall and secured to the edge of the wall.(Fig 6)
•
This floodlamp has the advantage that it can be connected to 230V since it is equipped with a built-in transformer on the cable.
•
In order to clearly light a pool it is recommended to install a floodlamp every 10 m2 of water surface.
•
In order to prevent glare, the floodlamps should be installed so that they face away from the residence or usual view of the
swimming pool.
Prior to installation verify that the gland seal (nº 10) has been fully tightened.
4. ASSEMBLY
This floodlamp has been designed for mounting primarily in an elevated swimming pool. It is supplied in 2 parts: the floodlamp unit
with the transformer and the appropriate cable, and the floodlamp support arm unit. There are three ways of placing the projector in
the swimming pool:
1. Standard: Standard Fastening:
Fig 1: Verify that the support arm unit is firmly secured to the elevated swimming pool floodlamp body (Nº 1)
Fig 2: Insert the cable in the groove in the support arm unit until the cable has reached the outside of the pool correctly.
Fig 3: Use screws to secure the support arm unit on the edge of the elevated swimming pool (Nº 15)
Connect the cable to the electric wiring.
2. Beach Fastening "Playa":
How to adapt the plastic hook to pools with metalic coping ("Playa")
Fig 7: Place the inox flange (nº 19) to the plastic hook (nº13) with the help of the plastic rivets (nº 21). Use a wood plug (nº 23)
and a small hammer (nº 24) to carry out this operation. Screw in the screw (no. 20) into the metallic flange.
Fig 8: Fix the support to one of the PVC profiles placed under the coping by using the screw (nº 20); before the screw reaches the
steel pool wall, place the rubber bumper (nº 22) between the wall and the screw.
Fig 9: Pass the electrical cord of the transformer (nº 18) over the PVC profile and place the coping on its position to protect the
cord.
3. Fastening with Hook:
Fig. 1. Check that the arm bracket unit is properly fastened to the raised pool projector Body (no. 1)
Fig. 2. Place the cable in the groove of the arm bracket unit until the cable comes out correctly on the outside of the pool.
Fig. 10. Fasten the arm bracket support to the raised pool edge, placing the Hook Bracket (no. 19) on the back part, using the
screws (no. 15) with the corresponding nuts (no. 17).
Connect the cable to the electrical installation.
5. MAINTENANCE
To remove the Floodlamp from the swimming pool, use a screwdriver to loosen the two screws (Nº 15) until they are fully
unscrewed. Remove the floodlamp unit and the support arm unit as though it were a single piece.
2