Controls And Functions - Black and Decker FL3WBD Manual De Instrucciones

Ocultar thumbs Ver también para FL3WBD:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

controls and functions

6
5
4
3
1
1. Rubber "O" ring
2. Translucent waterproof end cap (see detailed
view on page 5)
3. 12 volt DC charging port (for use with 120
volt AC charger and 12 volt DC charger)
4. Battery/charge status LED indicator
5. Rubber bezel
reaDiNg the BatterY/charge StatuS LeD iNDicator
The battery and charging status LED indicator is located directly above the 12 volt DC charging port
under the waterproof end cap on the back of the unit.
END CAP DETAIL
FL3WBD_ManualENSP_071713.indd 4-5
7
8
9
10
2
11
6. 3 watt LED bulb
7. Dimmer selector knob
8. On/off power knob
9. Grip handle
10. 120 volt AC charger
11. 12 volt DC charger (optional accessory)
DOT ICON (FOR
ALIGNMENT TO
THE TRIANGULAR
ICON ON THE
END CAP)
TRIANGULAR
ARROW
ICON (FOR
ALIGNMENT
TO THE DOT
ICON ON THE
REAR OF UNIT)
4
It lights or flashes in three colors to indicate the following:
When charging:
Green & Red (flashing alternately): Battery is overheated due to extensive use or recharging. The
charging process will stop at this stage and will automatically resume after a cool down period of
several minutes.
Green: Battery is in a fully charged state.
Orange: Battery is in a partially charged state.
Red: Battery needs to be recharged.
When operating:
Green: Battery is operating at full voltage.
Orange: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged.
Red (flashing): Battery is operating at extremely low voltage. The built-in low voltage protection has
activated and the unit will automatically shut down (after sounding several "beeps"). The unit must be
recharged immediately.
When using the dimmer selector:
Green (flashing): The light is adjusting to dimmer setting.
Red (flashing): The light is adjusting to brighter setting.
chargiNg/rechargiNg the SpotLight
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE first use using
either the 120 volt AC charger or the optional 12 volt DC charger for approximately 3-5 hours. Charge
after each use until the battery/charge status LED indicator lights green.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least every
30 days.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Make sure the unit is thoroughly dry before charging or recharging. If the unit has been submerged,
wipe it dry with a soft cloth before opening the end cap. If water leaks into the charging port, the
unit can sustain permanent damage.
• Never place the light face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor performance.
charging/recharging using the 120 volt ac charger
• Make sure the spotlight is turned off by rotating the on/off power knob to the furthest position
clockwise.
• Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
• Insert the barrel connector of the AC charger into the 12 volt DC charging port on the back of the
unit. Insert the plug end into a (powered) standard North American 120 volt 60Hz outlet.
• Charge until the battery/charge status LED indicator lights green (approximately 3-5 hours).
• Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end cap is
pointing to the dot icon on the rear of unit. Make sure it fits securely, but do NOT overtighten.
charging/recharging using the 12 volt Dc charger (optional accessory)
• Make sure the spotlight is turned off by rotating the on/off power knob to the furthest position
clockwise.
• Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
• Plug the barrel tip of the supplied 12 volt DC charger into the 12 volt DC charging port.
• Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power
source.
• Charge until the green battery status LED lights (approximately 3-5 hours). DO NOT CHARGE FOR
LONGER THAN 5 HOURS USING THIS METHOD.
• Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end cap is
pointing to the dot icon on the rear of unit. Make sure it fits securely, but do NOT overtighten.
Note:
When using a vehicle' s 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the
ignition to power the accessory outlet.
WARNING:TO AVOID THE RISK OF PROPERTY DAMAGE:
• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 Volt DC Adapter must only be connected to batteries with a nominal output voltage of 12
volts. The unit will not operate from a 6 volt battery and will sustain permanent damage if connected
to a 24 volt battery.
5
7/17/2013 7:26:48 PM

Publicidad

Tabla de contenido
loading

Tabla de contenido