The Dispenser Light - Whirlpool P6WB2L Manual Del Usaurio

IMPORTANT: You do not need to apply a lot of pressure to
the paddle to activate the ice dispenser. Pressing hard will not
make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for several seconds after
removing the glass from the dispenser paddle. The dispenser
may continue to make noise for a few seconds after
dispensing.
To Dispense Water (Standard):
1. Select water.
2. Press a sturdy glass against the dispenser paddle.
NOTE: While dispensing water and for 3 seconds after
dispensing has stopped, the digital display will show how
much water has been dispensed.
3. Remove the glass to stop dispensing.
To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specified amount of water
with the touch of a few controls.
NOTE: The amount of water you select will be dispensed. Be
sure that the container is empty and can hold the entire volume. If
ice is in the container, you may need to adjust your selection.
1. Press MEASURED FILL to turn on the feature. When the
feature is on, the Measured Fill screen appears on the display.
NOTES:
The dispenser will automatically turn off Measured Fill
after 1 minute of inactivity. When Measured Fill is turned
off, any changes you have made will be lost and all
defaults will be restored.
Press ICE/WATER, under Back, to manually turn off the
Measured Fill feature.
2. Press LIGHT, under Units, to toggle among ounce, cup and
liter. The default unit is ounce.
Default, minimum, and maximum volumes are listed below.
Units Default
Ounces 8
Cups 1
Liters 0.25
3. Press LOCK or OPTIONS to adjust the water volume as
desired. The LOCK control increases the volume, and the
OPTIONS control lowers the volume.
Minimum Maximum
1 128
¹/₄
16
0.05 4.00
RE F R I G E R A T O R U S E
NOTES:
When increasing or decreasing the dispense volumes, if
an adjustment button (-/+) is held for approximately
10 seconds or longer the control may stop responding.
Release the button for approximately 2 seconds and then
continue making the adjustment.
Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]
per cup) are not the same size as a measuring cup (8 oz
[237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
4. Dispense water.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
Press a sturdy glass against the dispenser paddle.
Place the glass below the water dispenser and press
MEASURED FILL, under Dispense, for hands-free
dispensing.
5. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser paddle OR
press MEASURED FILL a second time.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show how
much water remains to be dispensed. The display will turn off
after 1 minute of inactivity.
To select a new volume or start dispensing the same
volume again, you must first finish dispensing the
selected volume, or turn off the Measured Fill feature
(either by waiting 1 minute so it will automatically turn off
or by pressing ICE/WATER, under Back, to manually turn
it off) and then turn it back on.

The Dispenser Light

When you use the dispenser, the light will automatically turn on.
To turn on the light when you are not dispensing:
Press LIGHT to toggle through the following choices in a
continuous loop:
OFF (default) - The dispenser light is off
ON - The dispenser light remains on at 100% brightness
DIM - The dispenser light remains on at 50% brightness
The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see
"Troubleshooting" for more information.
ON
OR
DIM
23