BLACK&DECKER KD1001 Manual De Instrucciones página 6

ENGLISH
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-off button
3. Drilling mode selector
4. Chiselling mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Grease cap
Assembly
Warning! Before assembly, make sure that the tool is switched
off and unplugged.
Fitting the side handle and depth stop (fig. A)
Turn the grip counterclockwise until you can slide the side
u
handle (6) onto the front of the tool as shown.
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
u
Slacken the knob (9).
u
Insert the depth stop (7) into the mounting hole as shown.
u
Set the drilling depth as described below.
u
Tighten the knob (9).
u
Fitting an accessory (fig. B)
Clean and grease the shank (10) of the accessory.
u
Pull back the sleeve (11) and insert the shank into the tool
u
holder (5).
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked.
u
The hammering function requires the accessory to be able
to move axially several centimetres when locked in the
tool holder.
To remove the accessory, pull back the sleeve (11) and
u
pull out the accessory.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving
u
parts.
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When
u
using any tool for prolonged periods ensure you take
regular breaks.
6
(Original instructions)
Impairment of hearing.
u
Health hazards caused by breathing dust developed
u
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Selecting the operating mode (fig. C)
The tool can be used in three operating modes.
To operate the drilling mode selector (3), rotate it towards
u
the required position, as indicated by the symbols.
To operate the operating mode selector (4), push the
u
unlock button (12) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, and for
u
screwdriving set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
Hammer drilling
For hammer drilling in masonry and concrete, set the
u
operating mode selector (4) to the
drilling mode selector (3) to the
hammering, the tool should not bounce and run smoothly.
If necessary, increase the speed.
Hammering
For hammering with spindle lock, and for light chiselling
u
and chipping, set the operating mode selector (4) to the
position and the drilling mode selector (3) to the
position.
When changing from hammer drilling to chiselling, turn the
u
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the
spindle lock.
Setting the drilling depth (fig. D)
Slacken the knob (9).
u
Set the depth stop (7) to the desired position. The
u
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
Tighten the knob (9).
u
position and the
position. When