Bixolon BCD-1000 Guia De Instalacion

KN10-00003A (Rev.1.6)
◈ Information
This Installation Guide includes a brief outline of information necessary for product
installation. For more detailed installation information, please refer to the user manual in the
enclosed CD. The contents of the CD include the following.
1. Manual: User Manual
2. Drivers: Windows Drivers, OPOS Drivers
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
BCD-1000DN BCD-1000D
Common Components of All Products
Procuct Installation CD Procuct Installation CD Procuct Installation CD
CD Installation Guide
◈ Defaults & Options by Product Type
1. Serial Type
* Direct Type : Direct connection with the VFD, bypassing the Board
Item
Set
Default
Connection via a separate SMPS in the serial port
Connection
Power
Default
* Pass through Type (Data : Host (PC) → VFD → Printer)
Item
Set
Default
Board
Default
Power
Options
24V,2.5A:
K404-00007A
Cable
Options
BCD-1000WN BCD-1000W
Screws
M3*10, Tapping
(excluding BCD-1000D type)
VFD- Serial
Voltage Used: 5~24V (2pin)
12V (K410-00004C,D,E,F,H,I)
VFD- Serial
24V, 1.5A : 12V, 1.25A :
K402-00008B K410-00004C,D,E,F,H,I
9PM.25PF
(K604-00086A)
Power Cable 3P/3P 1.8M
(K610-00005B)
Power Cable 3P/2P 1.8M
(K610-00005G)
Display Installation Guide
CUSTOMER DISPLAY BCD-1000
◈ Connection Type and Size
Basic
Units
Interface
Power
Connection
Method 1
VFD Separate
Power Supply
Power
Connection
Method 2
SMPS→VFD
→Printer
Power
Connection
Method 3
SMPS→VFD
→Printer
Cable
9 pin
Connection
Method 1
Host→VFD
→Printer
9 pin
Cable
Connection
Method 2
9 pin
A: Power Supply Connector (Out DC 24V, 3pin)
B: Host Interface Connector (D-SUB 25pin, Female)
C: Power Supply Connector (In DC 5~24V, 2pin)
Etc.
D: Display Unit Connector
E: Printer Interface Connector (D-SUB 9pin, Male)
F: Power Supply Connector (In DC 24V, 3pin)
◈ Rotation Function
This product allows display rotation to any position or angle desired by the user. Please adhere to the
following instructions during installation to prevent possible product damage and/or malfunction. Following
assembly, follow the sequence below to fix the DISPLAY in the desired position.
Pole-Adjust
Nut-Fix
Pole-Main
(a) Lower the DISPLAY UNIT in the direction of the arrow.
Rotate the NUT-FIX to allow for lowering.
(Please refer to the product OPEN/CLOSE label.)
(b) Rotate the DISPLAY UNIT to the desired angle.
※ Caution
Do not rotate the DISPLAY UNIT in any direction for more that one full revolution.
(Beware as the DISPLAY UNIT can be rotated continuously.)
(c) After setting the DISPLAY to the desired position, secure the NUT-FIX.
(When raising the DISPLAY UNIT, lateral movement is prevented.)
Make sure to tighten the NUT-FIX after raising the DISPLAY UNIT to the desired height.
Caution
※
As excessive tightening of the NUT-FIX can result in product damage and/or
malfunction, secure only to the extent that the DISPLAY UNIT is fixed and does not
move.
※ Caution
As shown in figure (A), make sure to fully lower the DISPLAY UNIT before rotating.
Rotation of the DISPLAY UNIT when it is not fully lowered will produce a clicking
sound. This sound does not indicate any product breakage and is a result of the friction
between the POLE-MAIN RIB and the rotation section within the POLE-ADJUST.
If the DISPLAY UNIT is fully lowered, this sound will not be produced.
A B C
5~24V
3 pin 3 pin
3 pin
2 pin
25 pin
25 pin
25 pin
25 pin
(a) (b)
D E F
24V
24V
9 pin
(c)