Briteq Beam Matrix 5x5-RGBW Manual De Instrucciones página 9

ENGLISH
Browsing the setup menu:
General instructions for setup.
 Press the MODE button or UP/DOWN buttons to browse the different functions of the setup menu until the
required function is shown on the display.
 Press the ENTER button to access the function and change its parameters.
 The cursor of the value to change starts blinking. Use DOWN and UP button to change the value.
 Press the ENTER button again confirm and select the next parameter to adjust.
DMX ADDR
Used to set the desired DMX-address.
 Press the MODE button until the desired function is showing on the display.
 Press the ENTER button: the values can be changed
 Use DOWN and UP buttons to select the desired DMX512 address. The last occupied DMX-address is
also shown: makes it easier to set the address of the next unit in the chain.
 Once the correct address shows on the display, press the ENTER button to save it.
Note: on RDM-compatible controllers this option can also be remotely set.
CHANNEL MODE
Used to set the desired channel mode.
 Press the MODE button until the desired function is showing on the display.
 Press the ENTER button: the values can be changed
 Use DOWN and UP buttons to select the desired mode:
 4 CH RGB+DIM: RGB+Dim/sound for all 25pixels together (white color not used).
 4 CH RGBW: all 25 projectors together RGBW.
 5 CH RGBW+DIM: RGBW+Dim/sound for all 25pixels together.
 6 CH: RGBW+Dim/sound+Strobe for all 25pixels together.
 7 CH FX: Control of internal effects library (7 FX-channels)
 12 CH: RGBW+Dim/sound+Strobe+FX for all 25pixels together (as 6CH but with 6 extra FX-channels)
 25 CH WW 3200K: 25x channels with 25 pre-calibrated 3200K cold white pixels.
 25 CH CW 5600K: 25x channels with 25 pre-calibrated 5600K cold white pixels.
 25 CH CW 10000K: 25x channels with 25 pre-calibrated 10000K cold white pixels.
 100 CH: all pixels with separate RGBW control (pixel mapping)
 125 CH: all pixels with separate RGBW + DIM control (pixel mapping)
 150 CH: all pixels with separate RGBW + DIM + STROBE control (pixel mapping)
 Once the correct option shows on the display, press the ENTER button to save it.
Remark: on RDM-compatible controllers this option can also be remotely set.
SLAVE MODE
Used to set the projector as slave in a master/slave setup.
 Press the MODE button until SLAVE MODE is showing on the display.
 Connect the projector to a master.
Note: only to be used when the DMX-line in exclusively equipped with the same projector models.
SOUND MODE
Used to set the projector to standalone sound mode with different chases playing in endless loops.
Press the MODE button until "SOUND MODE" is shown on the display.
 Press the ENTER button: the sensitivity of the microphone (SENS) can be set from 00 to 31.
 Use DOWN and UP buttons to change the value.
 Press the ENTER button: the repetition rate (REP) of the chases can be set from 00 to 99.
 Use DOWN and UP buttons to change the value.
AUTO RUN (SIMPLE AUTO MODE)
Used to set the projector to standalone auto mode with different chases playing in endless loops.
Press the MODE button until "AUTO RUN" is shown on the display.
 Press the ENTER button: the playback speed of the chases can be set from 00 to 99.
 Use DOWN and UP buttons to change the value.
 Press the ENTER button: the repetition rate (REP) of the chases can be set from 00 to 99.
 Use DOWN and UP buttons to change the value.
BRITEQ
®
7/109
OPERATION MANUAL
BEAMMATRIX5x5-RGBW