Basic Tv Operation - LG 29FU6TS Manual Del Usuario

Basic TV operation

Before operating your TV, make sure the following
instructions have been completed.
• Your TV has been connected to an antenna or a
cable system.
• Your TV has been plugged in a power outlet.
• In this manual, the OSD (On Screen Display)
may be different from your TV's because it is just
an example to help you with the TV operation.
Turning on/off the TV
Press the POWER (or ON/OFF) button on
the set. At this time, the set switches to
standby mode and the standby indicator
lights up in red.
To switch the TV on from standby mode,
press the TV/VIDEO, CH
the set or POWER, TV/VIDEO, CH
number button on the remote control.
A channel number will be displayed on the
screen. The on-screen display will disappear
after a few seconds.
Press the POWER button on the remote
control. It reverts to standby mode.
To switch the TV off, press the POWER
button on the set.
Selecting the on screen language
1. Press the MENU button and then
until the menu is displayed as shown right.
2. Press the and then
G D
Language .
3. Press the and then use
G
select the desired language.
From this point on, the on-screen display will be
presented in the language of your choice.
4. Press the MENU button to exit.
Memorizing Channels
This is the function to memorize all the active
channels in your area before you can use the TV.
There are two ways of memorizing channels. You
can use either.
One is called AUTO PROGRAM and the other is
called MANUAL PROGRAM.
In AUTO PROGRAM the TV will memorize the
channels in ascending order. If there are
additional channels you want to add or delete, you
can manually add or delete those channels.
Memorizing the Channels by AUTO
PROGRAM
AUTO PROGRAM searches and memorizes all
the active channels in your area then you can
select the desired channel with the
Using the A.PROG button
You can conveniently perform AUTO PROGRAM
using the A.PROG button on the remote control.
1. Press the A.PROG button.
2. Press the or A.PROG button.The AUTO
G
PROGRAM starts now.
If you want to stop auto programming, press the
ENTER ( ) button.
A
Only the channels searched up to that time are
memorized.
Notes :
• If the programmed signal has poor quality,
memorize again in the
• AUTO PROGRAM stores all receivable channels
regardless of receiving signal (RF, Cable).
• If channels of general wireless TV and cable TV
are duplicated, press the number buttons (0 ~ 9)
to change as .
Using the MENU button
1. Press the MENU button and then use
button to select the channel menu.
2. Press the
/ button on Auto program
D
E
/ or 3. Press the
D
E
mode.
4. The AUTO PROGRAM starts now.
Memorizing the Channels by
MANUAL PROGRAM
Using the MEMORY/ERASE button
You can conveniently perform MANUAL
PROGRAM using the MEMORY / ERASE button
on the remote control.
/ button
D
E
1. Press the
/ button to select
E
the channel number you want to memorize or
/ button to erase.
D
E
2. Press the MEMORY/ERASE button to select
Memory
The on screen display appears as shown right.
Selecting the Channel
Press the
upper or lower channel then the channel being
viewed, or NUMBER buttons to directly select the
desired channel.
Adjusting the Volume
Press the
button to decrease the volume level.
F
To mute the sound, Press the MUTE button.
It's convenient when you get the telephone calls.
/ buttons.
D
E
To restore the muted sound, press the MUTE
button again or VOL
5
Auto program
Channels of
Channels of general
Cable TV
wireless TV
and then /
G D
E
.
button to enter the
G
/ or NUMBER buttons to select
D
E
or Erase .
/ button to conveniently select the
D
E
button to increase the volume level or
G
/ button.
F G
.
/
D
E
button to select
Auto program