FAAC 595 I/S Manual De Instrucciones página 24

Read the end user guide carefully before using the product
and keep it in a safe place for future reference.
GENERAL SAFETY INSTRUCTIONS
If correctly installed and operated, the 595 I/S automation
system ensures a high level of safety.
However, some simple rules should be followed to avoid
accidents:
- Do not pass underneath the door while it is moving: wait
until it is completely raised.
- Do not remain stationary under the door.
- Do not stand in the vicinity of the automation system or
allow anyone else, especially children, to do so, and do
not place objects in the vicinity of the automation system.
This is particularly important during operation.
- Keep remote controls or any other control device out of
the reach of children, to prevent them from accidentally
operating the automation system.
- Do not allow children to play with the automation system.
- Do not deliberately obstruct the movement of the door.
- Do not attempt to operate the door manually without first
unlocking it.
- In the event of a malfunction, unlock the door to allow
access and call a qualified technician for service.
- After manual operation, disconnect the electrical power
supply from the system before returning to normal
operation.
- Do not make any modifications to components belonging
to the automation system.
- Do not attempt to perform any repair work or tamper with
the automation system. Call qualified personnel for repairs.
- At least once every six months, have the automation
system, the safety devices and the earth connection
checked by a qualified technician.
DESCRIPTION
The 595 I/S automation system is an operator for
counterbalanced up-and-over doors. It is ideal for
controlling vehicle access areas up to 5 metres wide
(application with double operator) and with medium transit
frequencies.
Door operation is controlled by an electronic control unit
mounted in an enclosure which assures adequate
protection against atmospheric agents and can be fitted
inside the garage.
The normal position of the door is closed in a vertical
position. When the electronic control unit receives an
opening command from the remote radio control or any
other control device, it activates the hydraulic system and
causes the door to rotate upwards by 90° to the horizontal
position, thereby allowing access.
If automatic operation has been selected, the door closes
automatically after the selected pause time.
If semiautomatic operation has been selected, a second
impulse must be sent to close the door.
An open command given while the door is closing causes
the door to reverse direction of movement.
A stop command (if available) stops movement at any time.
END-USER GUIDE
THE 595 I/S AUTOMATION SYSTEM
For detailed information on door operation in the various
operating modes, contact the installation technician.
The automations may have safety devices (photocells)
which prevent the door from reclosing when an obstacle is
located in the area protected by them.
The 595 I/S automation system is fitted as standard with an
anti-crushing safety device that limits the torque transmitted
to the door.
The hydraulic system assures door locking in any position.
The door can be opened manually only after operating the
unlocking device.
MANUAL OPERATION
If the door must be operated manually because of a
power failure or malfunction, use the unlocking device as
follows.
Lever release device (see fig. 1)
SBLOCCA/UNLOCK
DEBLOQUE/ENTRIEGELT
DESBLOQUEAR
BLOCCA/LOCK
BLOQUE/VERRIEGELT
BLOQUEAR
SBLOCCA/UNLOCK
DEBLOQUE/ENTRIEGELT
DESBLOQUEAR
BLOCCA/LOCK
BLOQUE/VERRIEGELT
BLOQUEAR
External key release device (see fig.2)
- Insert the key in the lock and turn anticlockwise by one
turn.
- Open or close the door manually.
RETURNING TO NORMAL OPERATION
To prevent an accidental impulse from activating the door
during this operation, before returning to normal operation,
turn off the system's electrical power supply.
Lever release device (see fig. 1)
External key release device (see fig.2)
- turn the key clockwise until it stops.
- turn the key anticlockwise very slowly to the point where
it can be removed.
21
ENGLISH
Fig. 1
Fig. 2