V2 PROG2-USB Manual De Instrucciones página 26

If the learnt code is correct, PROG2 sends two sound impulses
and displays an error message (see ERROR MESSAGES
paragraph).
If the learnt code is correct, PROG2 sends one sound impulse and
the screen displays: (Example)
000 RX2
1 PDH30Y1 1 MONO
The pointer is automatically located under the channel selection
number.
Press one of the keys
NOTE: For the receiver modules it is possible that there are less
than 4 relay exits available. If for example the relays are only 2,
PROG2 permits in any case to set up relays 3 and 4, but they will
not correspond to any valid exit.
Press ENTER key to confirm the datum, the pointer moves
automatically for the function selection:
000 RX2
1 PDH30Y1 1 MONO
Press one of the keys
functions: monostable, bistable or timer.
Press ENTER key to confirm the datum
DO YOU CONFIRM?
ESC=NO
Press ENTER key to save modifications and exit from the
programming, on the screen the following appears:
000 RX2
1 PDH30Y1 1 MONO
MODIFICATION AND DELETION OF ONE OR
MORE MEMORY ZONES
When you need to delete or edit the content of one or more
memory zones of the receiver, it is necessary to read carefully the
following instructions.
A. Deletion of one engaged memory zone.
The screen must display the engaged memory zone to edit:
(Example)
068 RX2
3 KS*FGX0 2 BIST
Press ENTER key, the pointer is automatically positioned under
memory zone status indicator:
068 RX2
3 KS*FGX0 2 BIST
Press one of keys : set ups are deleted and the screen
displays
068 RX2
0 ####### 0 MONO
Pressing again keys the deletion is cancelled.
Pressing ESC key deletion is cancelled and PROG2 exits
automatically from the programming.
*
to select the desired relay.
*
for the selection of one of the three
ENTER=YES
*
*
*
Press ENTER key to confirm, the screen displays:
DO YOU CONFIRM?
ESC=NO
Pressing ESC key, PROG2 displays previous data and does not exit
from the programming.
Pressing ENTER key, PROG2 exits from the programming and
saves in memory the performed modifications.
B. Modifications of a memory zone set ups
The screen must displays:(Example)
068 RX2
3 KS*FGX0 2 BIST
Press more times ENTER key, the pointer moves showing the
current selection.
Pressing more times ESC key, the pointer goes back, until it exits
from the programming.
Press one of keys
selection.
Important: it is not allowed to replace the key number with a
memory one: as a matter of fact during the selection, the screen
displays only the enabled keys or the keys that are not stored.
After the modifications, press ENTER key until the screen displays:
DO YOU CONFIRM?
ESC=NO
Pressing ESC key, PROG2 displays previous data and does not exit
from the programming.
Pressing ENTER key, PROG2 exits from the programming and
saves in memory performed modifications.
RX DUPLICATION
This menu allows to transfer data stored in a transmitter of group
"A" all together to another receiver of the same group or group
"B".
Group A: RXP-1/50S, RXP-2/50S, RXP2S220, RXD1PP, RXD2PP,
PRGU433PP, PRGS433PP, PRGH433PP, PRGH433PLUS, PRGT-PP.
Group B: RX1, RX2, RX4, RX4PLUS, MR1, RXDPP10
The receivers of the group B are identified by means of PROG2
according to their model, while transmitters of the group A are
generically called "RX".
The screen must displays:
RX
ZONE CODIFIER
Press key , the screen displays:
RX
DUPLICATION
Press ENTER key, the screen displays:
INSERT RX
SOURCE
22
ENTER=YES
*
to change the set up of the current
ENTER=YES