Publicidad
Idiomas disponibles
Idiomas disponibles
e not
- Make sure that all the product's packaging has been
removed.
es not
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the
.
appliance.
place,
not in
Use:
o wa-
- Unroll the cable completely before plugging it in.
ected.
- Connect the appliance to the mains.
acing
- To save energy only switch the power tool on when
using it.
n use
Switching on:
- Press the On/Off Switch (4) to position I or II.
ildren
Switching off:
hot.
- Press the On/Off Switch (4) to position 0.
in ac-
nt the
Setting the air flow and temperature:
. Use
With the On/Off Switch you can selector between
ntend-
different temperatures and air flows combinations:
Setting
se.
Position I
y of a
Position II
Removing the heat protection:
nd.
- The heat protection collar (2) can be removed when
working at hard-to-reach locations.
- CAUTION: Increased danger of burning exists when
epair
working without the heat protection collar
- Unplug the appliance from the mains.
This
- Allow the hot air gun to cool down.
ained
or use
- Turn the heat protection collar (2) anticlockwise to
ability
remove and in clockwise direction to mount again.
Placing Down the power tool (Fig C):
- To cool down the power tool place it down on the
standing surface (3)
Working Advice
- The ideal temperature must be obtained by
performing a test
- The distance between the nozzle and the workpiece is
dependant of the material to be processed.
Remove paint/dissolving adhesives
- Soften the paint using the hot air gun and remove
evenly with the scraper.
- Do not heat for too long since this will burn the paint.
Removing paints from windows
- Always use the glass protection nozzle (5).
ºC
l/min
400
300
600
500
- Soften the paint using the hot air gun and remove
evenly with the scraper and a wire brush.
Shaping plastic tubing
- Use the reflector Nozzle
- To avoid kinking of the tubing, fill the tubing with sand
and seal at both ends.
- Heat the tubing evenly by moving it from side to side.
- Fit the cone
Staining wood
- Use the cone nozzle.
- Do not hold the nozzle too close to the wood as this will
color the wood unevenly.
- Sand off any singed wood fibres afterwards using fine
emery paper.
Shrink fitting
- Use the cone nozzle.
- Selector a proper heat-shrinkable sleeve.
- Heat the heat-shrinkable sleeve evenly.
Defrosting water pipes
- Do not attempt to defrost PVC piping.
- Use the reflector Nozzle
- Heat the frozen area inwards from the edge to the center.
Once you have finished using the appliance:
- Press the On/Off Switch (4) to position 0.
- Disconnect the appliance from the mains.
Safety thermal protector:
- The appliance has a safety device, which protects the
appliance from overheating.
Cleaning
- Disconnect the appliance from the mains and allow it to
cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains connection
with a damp cloth and dry. DO NOT IMMERSE IN WATER
OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few drops
of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning the
appliance.
- Do not let water or any other liquid get into the air vents to
avoid damage to the inner parts of the appliance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of cleanliness, its
surface may degrade and inexorably affect the duration of
the appliance's useful life and could become unsafe to use.
5
Publicidad
