Ozzyjuice - Chemfree SmartWasher 25C Manual De Operación

OzzyJuice

The SmartWasher uses a specially formulated
fluid which provides a combination of excellent
cleaning characteristics, safety and nutrition for
the Ozzy microbes. OzzyJuice is provided in
ready-to-use containers.
DO NOT ADD WATER, SOLVENT, MINERAL
SPIRITS, GASOLINE OR KEROSENE TO
YOUR SMARTWASHER!
To help monitor and maintain the proper fluid
level, the SmartWasher is equipped with a low
fluid level indicator. When the "Add Fluid" light
comes on, add a 5 gallon box of OzzyJuice
immediately. When a container of OzzyJuice is
added the light will go out. When the "Add
Fluid" light comes on, the heater will turn off
until the necessary amount of fluid is added.
Remember, the OzzyMat needs to be replaced
every 30 days.
To Add OzzyJuice
Slowly pour a full container of OzzyJuice
directly into the SmartWasher sink. The "Add
Fluid" light should go out.
If you add a container of OzzyJuice to your
machine and the "Add Fluid" light is still on, lift the sink off of the
base and check to see if the float is in the down position. If the
fluid is below the float and the float is not at the top stop, you will
need to add more fluid. If the fluid is over the float, there may be
a problem with the low fluid indicator and you should call your
service representative.
Temperature
Your SmartWasher should be plugged in 24 hours a day, 7 days
a week to maintain optimal temperature.
The thermostat is factory-set to maintain fluid temperature at
105° F (+-5°) (40° C) (+-3°). This temperature provides the
optimum condition for effective cleaning and activity of Ozzy
microbes.
The heater will not operate when the fluid level is low. Lift the
sink off of the base and visually check your fluid level. Your
SmartWasher should have approximately 8 inches (20 cm.) of
fluid in it. If lower than that, add OzzyJuice. If, after a reasonable
warm-up period, the fluid temperature seems too hot or too cold,
please refer to the "Troubleshooting" section on page 4.
If the temperature falls below the recommended minimum, the
system will still clean, and remediation of the hydrocarbons by the
Ozzy microbe colony will slow down but the microbes will not die.
The Ozzy colony will become more active when the fluid
temperature reaches the appropriate level.
PROPER USE AND CARE OF THE SMARTWASHER
To keep your new system operating at its best, please remember
these important hints:
Add Fluid
light
ChemFree Technical Support • 1-800-521-7182
• The heater is disabled as long as the "Add Fluid" light is on.
• The SmartWasher is designed to "eat" the oil and grease
washed from dirty parts. It is NOT designed to function as a
waste-oil dump! The Ozzy microbes will thrive on oil and
grease washed from parts during normal use. If excessive oil,
gasoline, transmission fluid, antifreeze or similar fluid is
dumped into the system, the Ozzy microbes may be
destroyed.
• DO NOT ADD - water, bleach, disinfectants, insecticides or
biocides of any description.
• Change the OzzyMat every month.
• Peel a layer off the OzzyMat every 7 to 10 days.
• To maintain the effectiveness of the SmartWasher, it is
imperative that nothing be added to OzzyJuice other than
replacement OzzyJuice or dirty parts residue.
• Turn off pump when not actually washing parts. This will help
to decrease fluid evaporation.
• Do not clean paint brushes in the SmartWasher.
OzzyMicrobes will not consume the inorganic pigments in
paint.
3