Silverline Silver Storm 264782 Manual De Instrucciones página 5

264782
4 - Keep other persons away - Do not let persons, especially children, not
involved in the work touch the tool or the extension cord and keep them away
from the work area
5 - Store idle tools - When not in use, tools should be stored in a dry locked-up
place, out of reach of children
6 - Do not force the tool - It will perform the job better and safer at the rate for
which it was intended
7 - Use the right tool - Do not force small tools to do the job of a heavy duty tool
Do not use tools for purposes for which they are not intended; for example do
not use circular saws to cut tree limbs or logs
8 - Dress appropriately
- Do not wear loose clothing or jewellery, which can be caught in moving
parts
- Suitable safety footwear is recommended when working outdoors.
- Wear protective covering to contain long hair
9 - Use protective equipment
- Use safety glasses
- Use face or dust mask if working operations create dust
WARNING: Not using protective equipment or appropriate clothing can cause
personal injury or increase the severity of an injury.
10 - Connect dust extraction equipment - If the tool is provided for the
connection of dust extraction and collecting equipment, ensure these are
connected and properly used
11 - Do not abuse the power cable - Never pull the power cable to disconnect
it from the socket. Keep the power cable away from heat, oil and sharp edges.
Damaged or entangled power cables increase the risk of electric shock
12 - Secure work - Where possible use clamps or a vice to hold the work. It is
safer than using your hands
13 - Do not overreach - Keep proper footing and balance at all times
14 - Maintain tools with care
- Keeping cutting tools sharp and clean makes the tool easier to control and
less likely to bind or lock in the workpiece
- Follow instructions for lubricating and changing accessories
- Inspect tool power cables periodically and have them repaired by an
authorised service facility if damaged
- Inspect extension cables periodically and replace if damaged
- Keep handles dry, clean and free from oil and grease
WARNING: Many accidents are caused by poorly maintained power tools.
15 - Disconnect tools - Disconnect tools from the power supply when not in use,
before servicing and when changing accessories such as blades, bits and
cutters
WARNING: The use of accessories or attachments not recommended by the
manufacturer may result in a risk of injury to persons.
16 - Remove adjusting keys and wrenches - Form the habit of checking to see
that keys and adjusting wrenches are removed from the tool before switching
it on
17 - Avoid unintentional starting - Ensure switch is in "off" position when
connecting to a mains socket, inserting a battery pack, or when picking up or
carrying the tool
WARNING: Unintended starting of a tool can cause major injuries.
18 - Use outdoor extension leads - When the tool is used outdoors, use only
extension cords intended for outdoor use and so marked. Use of an extension
cable suitable for outdoor use reduces the risk of electric shock
19 - Stay alert
- Watch what you are doing, use common sense and do not operate the tool
when you are tired
- Do not use a power tool while you are under the influence of drugs, alcohol
or medication
WARNING: A moment of inattention while operating power tools may result in
serious personal injury.
20 - Check damaged parts
- Before further use of tool, it should be carefully checked to determine that it
will operate properly and perform its intended function
- Check for alignment of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect its operation
- A guard or other part that is damaged should be properly repaired or
replaced by an authorised service centre unless otherwise indicated in this
instruction manual
- Have defective switches replaced by an authorised service centre
WARNING: Do not use the tool if the on/off switch does not switch it on and off.
The switch must be repaired before the tool is used.
21 - Have your tool repaired by a qualified person - This electric tool complies
with the relevant safety rules. Repairs should only be carried out by qualified
persons, otherwise this may result in considerable danger to the user
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the manufacturer
or an authorised service centre.
22 - Power tool mains plugs must match the mains socket - Never modify
the plug in any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching sockets will reduce risk of
electric shock
23 - If operating a power tool outside use a residual current device (RCD) -
Use of an RCD reduces the risk of electric shock
NOTE: The term "residual current device (RCD)" may be replaced by the term
"ground fault circuit interrupter (GFCI)" or "earth leakage circuit breaker (ELCB)".
WARNING: Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as that
specified on the nameplate of the tool. A power source with a voltage greater than
that specified for the tool can result in serious injury to the user, and damage to the
tool. If in doubt, do not plug in the tool. Using a power source with a voltage less
than the nameplate rating is harmful to the motor.
Polarized Plugs (for North America only) To reduce the risk of electric shock, this
equipment has a polarized plug (one blade is wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.
Electric Hoist Safety Instructions
• Before each use; inspect the steel cable for imperfections and weaknesses. Do
not use if the cable is frayed, kinked or wrapped improperly around the reel.
If the cable requires replacing do not replace with a cable of lesser strength.
Always leave at least three turns of the cable on the spool to ensure that the
hoist is able to lift the stated weight capacity
• Inspect the operator's controller before attempting to use the hoist. Do not use if
the controller is damaged. Avoid operating the hoist in damp or wet conditions
• Stand clear of any item being lifted by the hoist or underneath any item being
suspended by the hoist
• Do not hold the steel cable while lifting or lowering any item
• Never operate this tool alone, always have an extra person to help guide the
object being lifted
• Observe the maximum capacities and height limitations mentioned in the
specifications. Never exceed the figures
• Ensure the hoist is mounted to a beam which has a maximum capacity which is
double the capacity of the hoist. The beam should be at least 43mm in diameter
and have a wall thickness of at least 3mm
• The hoist is not designed for continuous use and the motor has an in- built
thermostat to prevent overheating and overloading. If the thermostat is
activated, the 'cool down' period will be approximately 5 minutes. If the motor
is exposed to direct sunlight it will severely reduce its operating time before the
thermostat will activate the 'cool down' period
• The electric hoist is fitted with an automatic shut off when it has reached its
highest point and lowest point. The height limiter is activated when the Stop
Block (9) reaches the Up Limit Lever (7). The lowering limiter is activated when
the cable reaches the lowest possible point and the cable is still safe to hold the
maximum load, the cable then engages with the Down Limit Lever (6).
• Always ensure that the unit is wound as shown:
• Never lift people or animals using this hoist. When operating the hoist always
keep bystanders and animals away from the load.
www.silverlinetools.com
500W Electric Hoist
5