General Inspection; Initial Or Annual Start-Up; Maintenance Schedule; Important - PMI CF2300 Serie Manual De Uso Y Cuidado

GENERAL INSPECTION

Initial Start-up or Annual Inspection
CAUTION:
Disconnect all electrical power to the cooler
before attempting to install, open, or service your cooler.
More than one disconnect will be required to de-energize
the equipment for servicing. If the cooler is
thermostatically controlled, the thermostat is not to be
used as the power supply disconnect, as it may reset and
start the unit unexpectedly.
Before start-up the cooler for the first time, or at the beginning of each
cooling season, make sure that all required connections,
adjustments, etc. have been made. Verify that:
Cooler mounting is level; ductwork is sealed.
Cabinet is securely fastened to mounting.
Cooler cabinet is properly grounded. Electrical connections
are correctly made, safe and secure.
Motor, pump, drain, bleed-off, float valve, etc. are correctly
installed and fully functional.
Water line securely connected, turned on, no leaks noted.
Float adjusted for proper water level.
Pump impeller turns free and smooth. If in doubt, remove
impeller cover (see "Cleaning Pump") and check rotation.
Fan blade, shaft, pulley and motor mounting bolts /
setscrews are tight.
Motor sheave / Fan blade pulley alignment okay; belt
correctly tensioned, fan blade turns freely.
Start-up Check List
CAUTION
: Never operate cooler with pad frames
removed. This will result in an overloaded condition and
may damage the blower motor.
To verify and check out the cooler installation on initial or annual start-
up, the following procedure should be followed.
Turn electrical supply to pump on.
Verify that pump starts and pads are evenly wet.
Open building exhaust / relief vents (windows, doors, etc.)
Turn electrical supply to blower motor on.
Observe that motor starts and runs, confirm air delivery.
Verify motor amperage does not exceed nameplate.
In case of trouble on any of these steps, refer to the Troubleshooting
Chart on page 8.
Cabinet Inspection Checklist
After initial start-up and for a few weeks afterwards, check for and/or
observe the following: Refer to the Troubleshooting Chart on
necessary.
Leaks from water lines, pad frames, cabinet, etc.
Cooler pads: even wetting, no dry streaks.
Confirm water level depth setting is correct.
Verify full, even flow in water distribution system.
Fan blade / motor rotates freely, no unusual noises.
Belt condition / tension / alignment OK.
Check motor mounting, cabinet hardware, setscrews on
pulleys, fan blade are tight.

Maintenance Schedule

Regular maintenance and periodic inspection is the key to long and
successful service from your Industrial Fan Cooler. The cooler should
receive major servicing at least once a year, more often if conditions
require (dusty environment, constant use, poor water quality, etc.) For
maximum cooling efficiency, long life and appearance, every two
months during operation, the cooler should be inspected and cleaned.
NOTE: Do Not Undercoat the Water Reservoir
Your cooler's water reservoir is finished with our Peblar XT®
appliance-type finish. It is so hard that asphalt-type cooler water pan
under-coatings will not stick to it. Undercoating will break free,
clogging the pump and water distribution system.
NOTE: Do not use cooler cleaners, cooler treatments, anodes or other
chemical additives in this evaporative cooler. Use of any additives or
water treatment other than the furnished bleed-off will void your
warranty and may impair the life of the cooler.
Before starting any maintenance operation, thoroughly read all
operating and maintenance instructions and observe all
cautions and warnings.
Cleaning
CAUTION:
garden hose; water may harm motor and pump or seep
through ductwork into building. Motors damaged by water
are NOT covered under warranty.
All foreign materials, mineral scale, hard water deposits, dirt, etc.
should be removed from pad frames, water pan and other
components. Your cooler's long lasting finish can be brought to like-
new condition by using warm water and a soft cloth.
NOTE: Avoid using scouring pads, steel wool or wire brushes, as
these will damage the finish and encourage corrosion.
Maintenance & Inspection

IMPORTANT:

of each cooling season, turn fan blade, cooler motor and
pump motor shafts by hand to make sure they turn freely.
Failure to do so may result in burning out motor.
Periodic inspection of your Industrial Fan Cooler will enhance the
chance for long, trouble-free service life. For maximum efficiency,
every two months during operation, or any time the cooler is opened,
the cooler should be inspected. Some suggested items to look for:
Check for leaks from pad frames, cabinet, etc.
Any dry spots or streaks on pads when pump is operating?
Are bolts, nuts and set screws still snug?
Are the bearings, etc., making any unusual noises?
Does the fan blade and motor turn freely?
Is float level set correctly?
page 8 i f
Is water in the bottom pan clean?
Belt condition / tension / alignment OK?
Adjust Belt Tension
Each time you inspect your cooler, be sure to check belt tension on the
motor/fan assembly. Check belt condition and replace it if frays or
cracks appear. Check alignment of fan blade pulley with motor pulley
(see page 4 for detailed steps).
Never wash your cooler cabinet with a
Before operating cooler at the beginning
I ndustrial Fan Evaporative Cooler - Use and Care Manual 5