Read Out; Offset Temperature; Application - CN ACG Manual Del Usuario

Type ACG/ADG
4 Press the Up or Down buttons until the Day option flashes. The cur-
rently selected day of the week will flash in the lower part of the display.
5 Press the Up or Down buttons until the required day of the week
flashes.
6 Press the OK button.
7 Select Exit to exit the option.
Please note: Usually, the electrician who installed the thermostat will have
set the correct time and day of the week.
Factory setting: Mon
DAY
SETTINGS
MON
FRI

Read Out

I want to know the amount of time (in per cent) that the heating
has been turned on within a certain period.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option flashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Readout option flashes.
5 Press the Up or Down buttons to the select the period of interest:
2 days, 30 days or 365 days. The percentage of time that the heating
has been turned on will then be indicated in the upper part of the
display.
The Readout submenu also contains information about the Software
version and the type of control (Room, Floor, Regulator or Room limit)
selected for the Application. (See Application for more information).
SETTINGS
READOUT

Offset Temperature

I want to adjust the difference in temperature between the ther-
mostat and my room thermometer.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option flashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Offset Temp option flashes.
5 Press the Up or Down buttons to set the offset temperature (in steps
of 1°).
TUE WED THU
SAT SUN
2 DAYS
30 DAYS
365 DAYS
SOFTWARE

APPLICATION

EXIT
6 Press the OK button.
7 Select Exit to exit the option.
Offset is used to compensate for any difference between the thermostat
and a room thermometer. It is possible to adjust the offset by up to +/-
10°C or +/- 18°F. Once the offset has been set correctly, the thermostat
will display the same temperature as the thermometer.
If, for example, the thermostat shows 1° too much, the offset should be
set to 1°. The temperature will then be set 1° lower.
SETTINGS
Application
I want to select the type of temperature control.
To do so, you must:
1 Press the OK button twice to activate the menu.
2 Press the Up or Down buttons until the Settings option flashes.
3 Press the OK button.
4 Press the Up or Down buttons until the Application option flashes.
5 Press the Up or Down buttons to select one of the four types of
control:
Room: The built-in room sensor is used. Only room temperature is
controlled.
Floor: A floor sensor is used. Only floor temperature is controlled.
Regulator: The thermostat functions as a simple regulator and no
sensors are used.
Room limit: The thermostat controls room temperature while using
the external temperature sensor as a limit sensor. If you choose this
option, you must set a maximum and minimum temperature for the
limit sensor, so that the thermostat will switch the heating off or on
if the temperature on the floor reaches the maximum or minimum
temperature respectively. This can, for instance, be used to avoid
excessively high temperatures on wooden flooring (maximum limit) or
excessively cold temperatures on tiled/stone flooring (minimum limit).
6 Press the OK button.
7 If Floor or Room limit is chosen, maximum and minimum floor
temperatures can now be set. Press the Up or Down buttons to set
the High temperature. Press OK and set the Low temperature. Press
the OK button.
8 Select Exit to exit the option.
Please note: Usually, the electrician who installed the thermostat will have
selected the correct type of temperature control for your application.
© 2012 OJ Electronics A/S
OFFSET TEMP
English
5