Secure Home SH-5597 Guia De Inicio Rapido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Motion Sensor
Light Control
Model SH-5597
Features
• D
Z
™ Technology.
UAL
ONE
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• D
B
Timer.
®
UAL
RITE
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
This package includes:
Lamp
Holders
Cover
Plate
Light Control
Mounting Strap
Mounting Bolt
Plastic Hanger
Rubber Plug
Requirements
• The Light Control requires 120-volts AC.
• If you want to use Manual Override, the control must
be wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with a junction box
marked for use in wet locations.
© 2006 DESA Specialty Products™
D
B
UAL
RITE
6 Screws
(3 sizes included)
Gasket
Sensor
2 Wire
Connectors
2 Lamps
(installed)
OPERATION
®
Mode:
On-Time:
Test
5 Sec
Auto
1, 5, 20 min.
Manual
Until Dawn*
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1
for the circuitry to calibrate.
Put ON-TIME switch
on the sensor bottom
toTEST and the D
UAL
B
switch OFF.
®
RITE
Put the ON-TIME switch in the 1,
5, or 20 minute position.
MANUAL MODE
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
Mode Switching Summary
TEST
AUTO
MANUAL MODE
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
D
UAL
Light comes on half bright for selected time after dusk
(Off, 3 hr., 6 hr., until dawn). If motion is sensed, the
light turns on full bright for the ON-TIME (1, 5, or 20
minutes) then returns to dim mode.
Works:
Day
x
/
1
2
TEST
D
B
ON-TIME
UAL
RITE
-
Off 3 6 Dusk to
TEST 1 5 20
Dawn
AUTO
ON-TIME
TEST 1 5 20
1 Second OFF
then...
... back on.
Move ON-TIME Switch to
1, 5, or 20 minutes
Flip light switch off
for one second then
back on*
B
TIMER
®
RITE
598-1162-01
Night
x
x
x
minutes
®

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Secure Home SH-5597

  • Página 1 1, 5, 20 min. Light Control Manual Until Dawn* * resets to Auto Mode at dawn. Note: When first turned on wait about 1 minutes Model SH-5597 for the circuitry to calibrate. Features TEST • D ™ Technology. Put ON-TIME switch ON-TIME ®...
  • Página 2 INSTALLATION ❒ The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger For easy installation, select an existing light with a wall can be threaded through the hole in the center of switch for replacement.
  • Página 3 TEST AND ADJUSTMENT ❒ Loosen the clamp screw in the Clamp sensor ball joint and gently Screw ❒ Turn on the circuit breaker and light switch. rotate the sensor. ❒ Walk through the coverage NOTE: Sensor has a 1 minute warm up period Ball area noting where you are before it will detect motion.
  • Página 4: Troubleshooting Guide

    TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE SYMPTOM POSSIBLE CAUSE Lights will Lights stay 1. Light switch is turned off. 1. A lamp is positioned too close to the not come on continu- 2. Light is loose or burned out. sensor or pointed at nearby objects ously.
  • Página 5: Detector De Movimiento Y Control De Luz

    ® TEST 1 5 20 RITE Dawn (TEST) y D ® RITE apagado (OFF). Modelo SH-5597 Características Para AUTOMATICO: • Tecnología D ™. ON-TIME Ponga el interruptor de tiempo • Prende la luz cuando detecta movimiento. (ON-TIME) en la posición de 1, 5 •...
  • Página 6: Instalacion

    INSTALACION ❒ Quite el aparato de luz existente. ❒ Instalelaláminademontajealacajadeempalmeusan- Para una fácil instalación escoja una luz con un do tornillos apropiados para la caja de empalme. interruptor de pared. ❒ Se puede usar el colgador plástico para sostener el CUIDADO: Para evitar los peligros de incen- aparato mientras se instala el cableado.
  • Página 7: Prueba Y Ajuste

    PRUEBA Y AJUSTE ❒ Fije la sensibilidad (RANGE) Tornillo como necesite. Demasiada Sujetador ❒ Prenda el cortacircuitos y el interruptor de luz. sensibilidad puede aumentar las falsas alarmas. NOTA: El detector tiene un período de cerca de 1 Unión ❒ Asegure la puntería de la ca- minutos de calentamiento antes de detectar Esférica beza del detector ajustando el...
  • Página 8: Guia De Investigacion De Averias

    GUIA DE INVESTIGACION DE AVERIAS SINTOMA POSIBLE CAUSA SINTOMA POSIBLE CAUSA La luz no se 1. El interruptor de luz está apagado. La luz se queda 1. Un faro está colocado demasiado cerca enciende. prendida con- 2. El faro está flojo o fundido. al detector o apunta a objetos cercanos 3.

Tabla de contenido