Product Description - Roger FIFTHY Serie Instrucciones Y Advertencias Para El Instalador

1
General safety precautions
Warning: incorrect installation may
cause severe damage or injury. Read
the instructions
installing the product.
This installation manual is intended for qualified personnel
only.
ROGER TECHNOLOGY cannot be held responsible for any
damage or injury due to improper use or any use other the
intended usage indicated in this manual.
Installation, electrical connections and adjustments must
be performed by qualified personnel, in accordance
with best practices and in compliance with applicable
regulations. Before installing the product, make sure it is
in perfect condition.
Disconnect the mains electrical power before performing
any work. Also disconnect any buffer batteries used.
Only use original spare parts when repairing or replacing
products. The packaging materials (plastic, polystyrene,
etc.) should not be discarded in the environment or left
within reach of children, as they are a potential source of
danger.
2

Product description

FIFTHY is a flashing warning lamp unit connectable to
ROGER TECHNOLOGY control units.
3
Technical characteristics
MAINS POWER VOLTAGE
MAX MAINS POWER
ABSORPTION
OPERATING
TEMPERATURE
DEGREE OF PROTECTION
N.B.: the FIFTHY flashing lamp unit is assembled with
thermosonic bonding technology to ensure an extremely
high protection rating.
In the event of breakage or malfunction, do not attempt
to repair the flashing lamp unit and contact the customer
support service or your dealer of choice.
4
Installation
• Ensure that the surface onto which the FIFTHY flashing
lamp unit is to be installed is level, clean and not subject
to vibration.
• Choose the mounting position: Figure 2 - top mounting
position; Figure 3 - lateral mounting position.
• Drill the mounting surface with a maximum bit size of
6 mm.
• Assemble the flashing lamp unit with the cable housing
base (A) at the bottom, as shown in fig. 2, or facing the
wall, as shown in fig. 3.
• Ensure that the cable passage and the mounting base
are sealed correctly if the mounting surface is not
perfectly even.
• Make the electrical connections as shown in fig.4
(FIFTHY/230V) or fig. 5-6 (FIFTHY/24V).
• If the 230 V version is used, protect the device with a
delayed action T500 mA fuse.
• Fasten the flashing lamp unit with the screws (B) and
commercially available anchor plugs (not included).
carefully before
FIFTHY/24 FIFTHY/230
230 Vac
24 Vac/dc
115 Vac
6,5 W 4 W
-20°C +55°C
IP55 IP55
5
Operation
Turn on the power supply.
Select the required flashing mode with the parameter 78
on the control unit (except for H70/10CC - 11CC). This
parameter is set as 78 00 by default (flash frequency 1 Hz,
0.5 s on, 0.5 s off).
If required, set the pre-manoeuvre warning flash function
with parameter A5 (except for H70/10CC - 11CC).
6
Disposal
The product may only be uninstalled by qualified
technical personnel, following suitable procedures
for removing the product correctly and safely. This
product consists of numerous different materials.
Some of these materials may be recycled, while
others must be disposed of correctly at the specific
recycling or waste management facilities indicated by local
legislation applicable for this category of product. Do not
dispose of this product as domestic refuse. Observe local
legislation for differentiated refuse collection, or hand the
product over to the vendor when purchasing an equivalent
new product. Local legislation may envisage severe fines for
the incorrect disposal of this product.
Warning! Some parts of this product may contain substances
that are harmful to the environment or dangerous and
which may cause damage to the environment or health
risks if disposed of incorrectly.
7
Additional information and
contact details
ROGER TECHNOLOGY is the exclusive proprietor holder of
all rights regarding this publication. ROGER TECHNOLOGY
reserves the right to implement any modifications without
prior notification. Copying, scanning or any alterations
to this document are prohibited without express prior
authorised from by ROGER TECHNOLOGY.
ROGER TECHNOLOGY CUSTOMER SERVICE:
business hours: Monday to Friday
08:00 to 12:00 - 13:30 to 17:30
Telephone no: +39 041 5937023
E-mail: service@rogertechnology.it
Skype: service_ rogertechnology
8
Declaration of Conformity
I the undersigned, as acting legal representative of the
manufacturer
Roger Technology - Via Botticelli 8, 31021 Bonisiolo di
Mogliano V.to (TV)
hereby DECLARE that the appliance described below:
Description: Flashing light
Model: FIFTHY
Is conformant with the legal requisites of the following di-
rectives:
– 2014/30/EU; – 2014/35/EU; – 2011/65/CE
and that all the standards and/or technical requirements
indicated as follows have been applied:
EN 61000-6-3; EN 61000-6-2
Last two figures of year in which marking was applied | 16.
Place: Mogliano V.to
Date: 20/12/2016 Signature
9