®
Architect
Series
1. Grasp both ends of the louver panel. Push the louver panel
straight up, then pull straight out. Lay the panel on a soft
surface.
2. Grasp both ends of the top grille. Push the top grille straight
up, then pull straight out. Lay the top grille on a soft surface.
2
1. Top grille
2. Cabinet side trim
3. Louver panel
3. Remove the 6 screws attaching each cabinet side trim to the
refrigerator and remove the side trims.
4. Stand the refrigerator up by first placing the left bottom edge
of the refrigerator on the floor, standing the refrigerator
upright and then lowering the right-hand side of the
refrigerator down to the floor.
5. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.
Pro Line™ Series
1. Grasp both ends of the top grille.
2. Push the top grille straight up, and then pull straight out.
3. Disconnect the wiring harness from the back of the top grille.
4. Lay the top grille on a soft surface.
5. Remove the 6 screws that attach each cabinet side trim to
the refrigerator, and remove the side trims.
6. Stand the refrigerator up. First, place the left bottom edge of
the refrigerator on the floor, stand the refrigerator upright and
then lower the right-hand side of the refrigerator to the floor.
7. After the dolly has been removed from the refrigerator,
reassemble the trim.
8. Reattach wiring harness into grille back.
9. Insert top grille hooks into slots on the side trim. Pull grille
down slightly to lock into place.
1
2
3
Install Anti-Tip Boards
IMPORTANT:
The solid soffit must be within 1 in. (2.5 cm) maximum above
the refrigerator. If the solid soffit is higher than 1 in. (2.5 cm) or
one is not available, prevent the refrigerator from tipping
during use as shown.
It is recommended that board(s) be installed before the
refrigerator is installed.
Board(s) must be long enough to fully cover the width of the
compressor cover.
Locate the board(s) so the bottom surface of the board(s) are
84 in. (213 cm) from the floor.
During installation, raise the refrigerator up so there is
¹⁄₄ in. (6.4 mm) maximum between the top of the refrigerator
and the bottom of anti-tip board(s). Do not crush the
condenser cover when raising the rear leveling legs.
To install anti-tip boards
1. Mark the stud locations on rear wall 80 in. to 90 in. (203 -
229 cm) above floor.
2. Securely attach one or two 2 in. x 4 in. x 32 in.
(5 cm x 10 cm x 81 cm) wood boards to wall studs behind
refrigerator. Use 6 - #8 x 3 in. (7.6 mm) (or longer) wood
screws. The wood screws must be screwed into the studs at
least 1½ in. (3.8 cm). The board(s) must overlap the
compressor cover.
2" (5 cm)
4
1. Center board ¹⁄₄ in. (6 mm) max. above refrigerator
2. Two 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) boards
3. Attach to studs with 6 -#8 x 3 in. (7.6 cm) screws
4. Compressor cover
Connect Water Supply
1. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
2. Before attaching copper tubing to the refrigerator, flush at
least 2 qt. (1.9 L) of water through the copper tubing and into
a bucket to get rid of any particles in the water line.
3. Check for leaks around the saddle valve. Do not overtighten
the clamp or sleeve. This will crush the copper tubing.
4. Make connection to the refrigerator.
Style 1 - Connecting to a Water Valve:
NOTE: The water shutoff valve should be located in the base
cabinet on either side of the refrigerator. The right-hand side
is recommended. The access hole through the right cabinet
must be within ¹⁄₂ in. (12.7 mm) of rear wall.
1
2
3
19