Sales & Homologation - KLIM Alpride E1 Atlas 26 Manual Del Usaurio

TRANSPORT & TRAVEL
12
The KLIM ALPRIDE® E1 AIRBAG SYSTEM uses only 2 x AA batteries. The KLIM ALPRIDE® E1 AIRBAG SYSTEM has no Li-Ion / Li-Po
battery, no gas cartridges under pressure and no pyrotechnic trigger.
The KLIM ALPRIDE® E1 AIRBAG SYSTEM has no restrictions for travelling and shall not be considered as Dangerous Good in the
meaning of the Dangerous Goods Regulations.
Even though there are absolutely no restrictions for travelling with the KLIM ALPRIDE® E1 AIRBAG SYSTEM, to avoid any
misunderstanding with airport security agents, we recommend to announce to the airlines that you are travelling with an electrical
avalanche airbag WITHOUT battery. The KLIM ALPRIDE® E1 AIRBAG SYSTEM has a pressure relief valve system.
TROUBLE SHOOTING
13
MALFUNCTION
The airbag doesn't inflate when pulling trigger?
The autotest doesn't work?
The autotest is KO –> Check LED
Airbag does not inflate fully:
The system does not charge from the AA batteries?
ADDITIONAL INFORMATION
14
PRODUCT DESCRIPTION
Type: KLIM ALPRIDE® E1 AIRBAG SYSTEM backpack
USB 5V DC 2A / 2 X AA / LR6 1.5 V
Operating Temperature: - 30°C / + 40°C
IP65 conform controller
Patent No: EP3202462
SERVICE CENTER
The ALPRIDE® E1 AIRBAG SYSTEM customer service center for the different countries are listed under our website www.alpride.swiss.
SALES & HOMOLOGATION
15
SALES
Responsible for the development and commercialization in the EU and worldwide is:
ALPRIDE® SA, Chemin des Chômeurs 2, 2523 Lignières, Switzerland
All information related to importers is available at www.alpride.swiss
HOMOLOGATION
All declarations of conformity are available at www.alpride.swiss
Tested by TÜV Süd Product Service GmbH, Daimlerstr. 11, 85748 Garching bei München, Germany. Prüfstellennummer 0123.
Certified according to: EN 16716: 2017
The KLIM Alpride® avalanche backpacks comply with the provisions and safety requirements of the European Standard EN 16716: 2017
for Mountaineering equipment – Avalanche airbag systems – Safety requirements and test methods.
All homologated backpacks are labelled with corresponding seals indicating they have passed the official tests. They are affixed in plain
sight and may not be removed.
TROUBLE SHOOTING
1- Is the E1 On? –>Check LED
2- Are the supercapacitors charged enough (LED orange or
green)?
3- Is the autotest ok? –>Check LED
The supercapacitors are not charged enough to run the
motor?
–>Wait for orange or green LED
The compressor cover was not well closed and something,
material is blocking the compressor wheel and preventing to
turn.
There might be any of the following reasons for the
malfunction:
1- If the airbag is rolled instead of properly folded
2- Because there is a webbing or something covering and
restraining the zipper
3- The deflating knob is blocked in deflating position and
prevent the non-return valve to close properly
Make sure you are using brand new, premium quality alkaline
or lithium AA / LR6 batteries.
Do not use AA zinc carbon batteries and NiCd or NiMH
accumulators (rechargeable).
SPECIFICATIONS
Weight of complete E1 SuperCap kit (without batteries): 1'280
g. +/- 10 g
Total volume of the complete airbag kit in backpack: 2.3 litres
Micro-USB: 5V – 2A DC
Batteries: 2 x AA / R6 / UM3 1.5 V Alkaline or Lithium
Certification: CE according to EN 16716 standards set by TÜV
Süd GmBH
Model: Alpride® E1
USER MANUAL / ENGLISH 13