Energizing The Thermostat; Personalizing Your Floor Comfort Schedule - Warm Tiles GTS-1 Instrucciones De Instalación Y Operación

C. Energizing the Thermostat
When power is first connected to the thermostat, the LCD Display flashes as shown. After 90 seconds the display will stop flashing and go to the default time
setting of Monday, 12:00 AM and display the Floor Temp. The display will also stop flashing if a program button is pressed, or the mode switch is moved to
another position.
D. Setting the Time and Day
1. Move the mode switch to the OFF position; the actual Floor Temp and current time are displayed.
2. To enter the time setting program, simultaneously press and hold the BACK and the ACCEPT buttons for 3 seconds. The Day symbol flashes. Press the UP (s)
or DOWN (t) button to adjust the Day. Press the ACCEPT button once to accept the Day setting.
3. After accepting the Day setting, the AM or PM symbol flashes. Press the UP (s) or DOWN (t) button to set AM or PM. Press the ACCEPT button once to
accept the AM/PM setting.
4. After accepting the AM or PM setting; the Hour digits flash. Press the UP (s) or DOWN (t) button to set Hour. Press the ACCEPT button once to accept the
Hour setting.
5. After accepting the Hour setting; the Minute digits flash. Press the UP (s) or DOWN (t) button to set the Minute. Press the ACCEPT button once to accept
the minute value and exit the time setting program.
During the previous steps, if no key input is received for 90 seconds or the mode switch is moved to other position, the program will exit the time setting mode
and reset to the Default value of 12:00 AM, Monday. The time is now set, the thermostat clock will start running.
E. Selection of Temperature Scale
(Fahrenheit or Centigrade)
1. Move the mode switch to the MANUAL position; the Floor Temp and current time are displayed.
2. To enter the temperature scale selection; simultaneously press and hold the BACK and the ACCEPT buttons for 3 seconds. The "F" or "C" digit flashes.
3. Press the UP (s) or DOWN (t) button to toggle between F and C .
4. Press the ACCEPT button once to accept the F or C scale and exit the setting.
F. Quick Start
The thermostat is pre-programmed for immediate use. To begin setback operation in the 5/2 mode, move the Mode switch to the Auto position;
thethermostat will control the floor temperature to a moderate temperature (86°F/30°C) such that the cables are only energized in the morning and the
evening, and off during the day and the night. The exact schedule of operation is as follows:
If setback operation is not required, move the Mode switch to the Manual position. The floor temperature is preset to 86°F (30°C), and can be adjusted up or
down by simply pressing and holding the UP (s) or DOWN (t) button for 1 second (temperature display will flash) and then repressing the UP (s) or DOWN
(t) button for each degree that you want to increase/decrease. Display stops flashing when UP (s) or DOWN (t) button is not pressed for 5 seconds, and
then the new temperature setting goes into effect. If floor heating is not required at this time, set the Mode switch to OFF. The display will continue to show
the time and the floor temperature.
Automatic Program for Weekdays
Time
Wake 6:00 am
Leave 8:00 am
Return 5:00 pm
Sleep 10:00 pm
Automatic Program for Weekends
Time
Wake 6:00 am
Leave 8:00 am
Return 5:00 pm
Sleep 10:00 pm
G. Personalizing Your Floor Comfort Schedule
The GTS series thermostats offer two programming modes to personalize your floor comfort and maximize energy savings. The first program mode is the 5/2
Day mode, which groups Monday – Friday as the "5" group and Saturday and Sunday as the "2" group. The second program mode is the 7 Day mode, which
allows you to program each day individually to suit your specific schedule. Each program mode allows four unique time/temperature settings ("events").
Usually, you would select the program mode that best suits your schedule. (Hint: It is easier and quicker to modify the 5/2 Day program than the 7 Day
program, so choose the 5/2 Day if it better suits your schedule.)
Both the 5/2 Day and 7 Day modes are pre-programmed, as noted in "Quick Start" above. These programs are easily modified, as explained in the
appropriate sections below.
Prior to modifying these programs, you should consider that floors take time to heat up and cool down to their set temperatures. Keep in mind that you may
want to set the Floor Temp about one hour before you want the floor to be warm, this allows adequate heat up time. Conversely, you can set the Floor Temp
to decrease about one hour before you want the floor to reach its cool down temperature.
Most floors feel comfortable between 80°F (27°C) and 86°F (30°C). For a variety of reasons, in certain installations the comfortable temperature may be
above or below this range; this is normal. The maximum setting on the thermostat is 104°F (40°C) In most installations it is unlikely that the floor will ever reach
this temperature; this, too, is normal.
Floor Temp
86°F/30°C
60°F/16°C
86°F/30°C
60°F/16°C
Floor Temp
86°F/30°C
86°F/30°C
86°F/30°C
60°F/16°C
5