Intended Use; Safety Instructions; On/Off Switch; English - Black and Decker BDS100 Manual Del Usuario

Intended use

This Black & Decker tool has been designed to detect studs
covered by wall boards. This tool is intended for consumer use
only.

Safety instructions

Warning! When using battery-powered tools, basic
x
safety precautions, including the following, should always
be followed to reduce the risk of fire, leaking batteries,
personal injury and material damage.
Read all of this manual carefully before operating the tool.
x
Retain this manual for future reference.
x
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts.
Preferably wear rubber gloves and non-slip footwear when
working outdoors. Wear protective hair covering to keep long
hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles. Wear ear
protection whenever the sound level seems uncomfortable.
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool for damage.
Check for misalignment and seizure of moving parts, breakage
of parts, damage to guards and switches and any other
conditions that may affect its operation. Ensure that the tool
will operate properly and perform its intended function. Do not
use the tool if any part is damaged or defective. Do not use
the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Store idle tools
When not in use, tools and batteries should be stored in a dry,
locked up or high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
Additional safety instructions for non-rechargeable
batteries
Never attempt to open for any reason.
x
Do not store in locations where the temperature may
x
exceed 40 °C.
When disposing of batteries, follow the instructions given
x
in the section "Protecting the environment".
Do not incinerate the batteries.
Under extreme conditions, battery leakage may occur.
x
When you notice liquid on the batteries, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
Features

1. On/off switch

2. LED indicators
Assembly
Fitting the batteries (fig. A)
Depress the release button (4) and slide the battery cover
x
(3) off the tool.
Insert the batteries into the tool in the orientation as shown.
x
Refit the cover and let it click into place.
x
Use (fig. B)
Place the tool flat against the wall as shown.
x
Keep the on/off switch (1) depressed.
x

ENGLISH

3