Technical Data - Martin Yale Industries MY 1000 SC Instrucciones De Uso

GB
CLEANING THE PHOTOCELLS (Fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes" of the photocell with a brush.
MATERIAL JAM IN MACHINE:
(Auto-stop-function)
If too much material is fed in, causing a jam, the
machine will respond as follows:
- The cutting system blocks and stops.
Cutting mechanism halts, then runs one step in
reverse (material will be released) and stops.
- The motor shuts down automatically.
- The pilot lamp (4) (fig. 1) lights up.
Proceed as follows:
- Turn the function switch (1) (fig. 1) briefly to
position „ " (material will be released), then in
position „ ".
- The pilot lamp (4) (fig. 1) goes out.
Paper jam in the paper feed slot (6)
- Tear off the excess paper over the feed slot and
then turn the function switch (1) (fig. 1) to
position „ ".
- The cutting system then runs forward and shreds
the paper remaining in the cutter.
- Continue shredding, feeding smaller quantities
of paper.
Material jam in the security feed slot (7)
- Remove the returned material.
Take care when removing material
as sharp edges may cause injury.
- Turn the function switch (1) (fig. 1) in position
„ ".
- The remaining material to be shredded is then
fed to the cutting system again.
- Once the remaining material has been shredded,
continue shredding, feeding the correct
quantities.
Description
Lubricant, 125 ml bottle
Note: For orders of special accessories and spare parts, please contact your dealer.
MAINTENANCE
MALFUNCTIONS
- If required, switch the cutting system alternately
to forward and reverse until all of the material
has been run through the cutting system and
shredded.
Wait each time until the motor stops
before switching direction (position
„ ").
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. The pilot lamp (5) (fig. 1)
lights up. Turn the machine off with the function
switch (1) (fig. 1) (position „ ").
Allow the motor to cool down for 20 to 25 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the following:
- Is the plug connected to the mains?
- Is the function switch (1) on?
- is the receptacle placed properly under the
machine?
- is there a material jam in the machine?
Follow the instructions under "MATERIAL JAM"
- has the motor been overloaded?
Wait until the motor has cooled, and then restart.
If none of the above applies, please contact
your dealer.
ACCESSORIES
2
fig. 4
Order-No.
99943
5
MY 1000 SC
MY 1000 CC
MY 2000 SC
MY 2000 CC
MAINTENANCE
CUTTING BLOCK (3.8x48 mm):
After approximately 15 minutes of continuous
operation, switch to reverse running for about 15-
20 seconds and during this time spray some of the
special oil on to the cutting mechanism (refer to
"ACCESSORIES" for the order number).
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched
off over night (Turn the function switch (1) (fig. 1) in
position „ ").

TECHNICAL DATA

Cutting width:
MY1000SC: 4 mm
MY1000CC: 3.8x48 mm
MY1000SC: 4 mm
MY1000CC: 3.8x48 mm
Cutting capacity paper:
MY1000SC: 10-12 sheets (70g/m
MY1000CC: 7-9 sheets (70g/m
MY2000SC: 14-16 sheets (70g/m
MY2000CC: 9-12 sheets (70g/m
Cutting capacity
Credit cards/CD's/DVD's:
feed one at a time
Supply voltage: 230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing: 10 amps (slow-blow)
Noise level: approx. 65 dB(A)
Power: 0.7 kW
Dimensions:
MY1000SC/CC:
Width: 350 mm
Depth: 350 mm
Height: 560 mm
MY2000SC/CC:
Width: 400 mm
Depth: 300 mm
Height: 602 mm
Weight:
MY1000SC: ca. 7 kg
MY1000CC: ca. 8 kg
MY2000SC: ca. 10 kg
MY2000CC: ca. 12 kg
2
)
2
)
2
)
2 )