Publicidad
Idiomas disponibles
Idiomas disponibles
"MICROLOCK
"MICROLOCK " RETENTION SYSTEM
Your new helmet is equipped with the exclusive "Microlock " retention system, which is
Your new helmet is equipped with the exclusive "Microlock
one of the most comfortable and modern systems available today thanks to its microme-
one of the most comfortable and modern systems available today thanks to its microme-
tric regulation. In order to have the maximum protection and to appreciate the advanta-
tric regulation. In order to have the maximum protection and to appreciate the advanta-
ges of the "Microlock " system, carefully read the instructions contained in this label. Put
ges of the "Microlock
your new on, making sure the size is correct (see enclosed instructions manual).
your new Nolan on, making sure the size is correct (see enclosed instructions manual).
1. Attach the "Microlock " by inserting the dented tongue in the buckle ➊.
1. Attach the "Microlock
Warning: Do not twist the strap; the dented part of the tongue must be facing the out-
Warning: Do not twist the strap; the dented part of the tongue must be facing the out-
side of the helmet.
side of the helmet.
Pull on the chin strap to make sure the locking mechanism is engaged.
Pull on the chin strap to make sure the locking mechanism is engaged.
2. Press the dented tongue completely, until you feel the strap press against your cheek.
2. Press the dented tongue completely, until you feel the strap press against your cheek.
Warning: The tongue should not move freely in the locking mechanism.
Warning: The tongue should not move freely in the locking mechanism.
3. Now try to take off your helmet by puling it from the back edge, rotating it towards the
3. Now try to take off your helmet by puling it from the back edge, rotating it towards the
front; the helmet must remain well fixed on your head (see enclosed instructions).
front; the helmet must remain well fixed on your head (see enclosed instructions).
4. If while performing step 3 you notice that the chin strap is too loose (this can be deter-
4. If while performing step 3 you notice that the chin strap is too loose (this can be deter-
mined by insufficient pressure on the jaw when the dented tongue is fully inserted in
mined by insufficient pressure on the jaw when the dented tongue is fully inserted in
the locking mechanism), then the strap must be pre-adjusted (shorten the chin strap).
the locking mechanism), then the strap must be pre-adjusted (shorten the chin strap).
If while performing step 3 you notice that the chin strap is too tight (this condition can
If while performing step 3 you notice that the chin strap is too tight (this condition can
be determined if the chin strap is too tight when the dented tongue is on the third or
be determined if the chin strap is too tight when the dented tongue is on the third or
fourth click), then the chin strap must be lengthened.
fourth click), then the chin strap must be lengthened.
5. To make a pre-adjustment, release the helmet by lifting the red lever. Slip the helmet
5. To make a pre-adjustment, release the helmet by lifting the red lever. Slip the helmet
off ➋.
off ➋.
Adjust the chin strap length by passing the strap through the metal adjusting buckle ➌.
Adjust the chin strap length by passing the strap through the metal adjusting buckle ➌.
6. Repeat steps 1 through 3 taking care that the dented tongue has effected at least 5
6. Repeat steps 1 through 3 taking care that the dented tongue has effected at least 5
clicks into the body of the locking mechanism.
clicks into the body of the locking mechanism.
(We recommend performing the pre-adjustment by sliding the fastening flap by least
(We recommend performing the pre-adjustment by sliding the fastening flap by least
5 notches so as to make the most of the adjustment function of the "Microlock
5 notches so as to make the most of the adjustment function of the "Microlock
system. By sliding or releasing the fastening flap by one notch as to the pre-adju-
system. By sliding or releasing the fastening flap by one notch as to the pre-adju-
stment, the system ensures the best comfort guarantying the fastening safety).
stment, the system ensures the best comfort guarantying the fastening safety).
7. WARNING!!! LIFT THE RED LEVER ONLY WHEN YOU ARE REMOVING YOUR HEL-
7. WARNING!!! LIFT THE RED LEVER ONLY WHEN YOU ARE REMOVING YOUR HEL-
MET! NEVER RELEASE THE LEVER WHILE DRIVING!
MET! NEVER RELEASE THE LEVER WHILE DRIVING!
CARE OF "MICROLOCK " RETENTION SYSTEM
CARE OF "MICROLOCK
The effectiveness of the adjustment and retention system can be impaired by dust or
The effectiveness of the adjustment and retention system can be impaired by dust or
sand. We suggest periodic cleaning of the "Microlock " retention system using only a
sand. We suggest periodic cleaning of the "Microlock
solution of luke-warm water and neutral soap.
solution of luke-warm water and neutral soap.
USE NOT SOLVENT, DO NOT LUBRICATE.
USE NOT SOLVENT, DO NOT LUBRICATE.
Manipulations or unusual events, which can compromise the working of the retention
Manipulations or unusual events, which can compromise the working of the retention
system cannot be excluded.
system cannot be excluded.
If the "Microlock " system is not functioning properly discontinue the use of the helmet.
If the "Microlock
1
2
1
" RETENTION SYSTEM
1
2
" system, carefully read the instructions contained in this label. Put
" by inserting the dented tongue in the buckle ➊.
1
2
2
1
" RETENTION SYSTEM
2
" system is not functioning properly discontinue the use of the helmet.
1
2
" retention system using only a
1
4
4
2
" retention system, which is
GB
GB
1
''
2
"
Publicidad
