General Maintenance - Ryobi RBV26 Manual De Utilización

Deutsch (Übersetzung der originalen Anleitungen)
throttle setting.
To release the cruise control, push cruise control
n
lever all the way towards the front of unit.
VACUUM OPERATION
See Figure 11.
WARNING:
Keep the silencer and all hot surfaces of the
blower/vacuum away from your body. Failure to
do so could result in possible serious personal
injury.
Install the vacuum tubes and the bag. Refer to the
n
"As sembly" section earlier in this manual.
Start the blower. Refer to "Starting and Stopping"
n
earlier in this manual.
Place the vacuum bag strap over your right shoulder.
n
Hold the upper handle in your left hand and the
vacuum handle in your right hand.
Move the blower/vacuum from side to side along
n
outer edge of the debris. To avoid clogging, do not
place the vacuum tube directly into the debris pile.
Hold the engine higher than the inlet end of the
n
vacuum tube.
Always point vacuum tube downhill when working on
n
a hillside.
■ To avoid serious injury to the operator or damage to
the unit, do not attempt to suck rocks, broken glass,
bottles, or other similar objects.
■ If the vacuum tubes should clog, stop the engine,
ensure impeller blades have stopped spinning, and
disconnect the spark plug wire before cleaning out the
obstruction.
Remove the vacuum tubes and clear the debris from
n
the blower fan housing. Remove the bag and clear
the tube. A small rod or stick may be required to clear
the entire tube length. Ensure that all debris has
been cleared before reassembling the vacuum tubes.
MAINTENANCE
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING:
Always wear eye protection with side shields
marked to comply with EN166, along with
hearing protection. Failure to do so could result
in objects being thrown into your eyes and
other possible serious injuries.
WARNING:
Before inspecting, cleaning, or servicing the
machine, shut off the engine, wait for all moving
parts to stop, disconnect the spark plug wire
and move it away from the spark plug. Failure
English (Original instructions)

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from various
commercial solvents. Use clean cloths to remove dirt,
dust, lubricant, grease, etc.
You can often make adjustments and repairs described
here. For other repairs, have the blower/vacuum serviced
by an authorized service dealer.
CLEANING THE AIR FILTER
See Figure 12 - 13.
For proper performance and long life, keep air filter clean.
n
n
n
n
CLEANING THE EXHAUST PORT, SILENCER AND
SPARK ARRESTOR
Depending on the type of fuel used, the type and amount
of lubricant used, and/or your operating conditions, the
exhaust port, silencer, and/or spark arrestor screen may
become blocked with carbon deposits. If you notice a
power loss with your petrol-powered tool, you may need
to remove these deposits to restore performance. We
highly recommend that only qualified service technicians
perform this service.
It is recommended to clean or replace the spark arrestor
every 50 hours or yearly to ensure proper performance
of your product. Spark arrestors may be in different
locations depending on the model purchased. Please
contact your nearest service dealer for the location of the
spark arrestor for your model.
VACUUM BAG
A dirty bag will reduce performance. To clean the bag,
turn it inside out and shake. Wash the bag in soapy water
at least once a year.
FUEL CAP
The fuel cap contains a non-serviceable filter and a
19 19
to follow these instructions can result in serious
personal injury or property damage.
WARNING:
Do not at any time let brake fluids, petrol,
petroleum-based products, penetrating
lubricants, etc., come in con tact with plastic
parts. Chemicals can damage, weaken or
destroy plastic which may result in serious
personal injury.
Remove the air filter cover by turning the dial counter
clockwise while gently pulling on the cover.
Rinse filter with clean water.
Gently squeeze filter until excess water is removed.
Replace the filter.
Place the air filter cover back on the unit. Turn dial
clockwise until cover is secure.
WARNING:
To avoid a fire hazard, never run the blower/
vacuum without the spark arrestor in place.
WARNING:
A leaking fuel cap is a fire hazard and must be
replaced immediately.