Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Part No.: 7610.714.18
Catalog No.: 3227469
Rev. A
01/11
Instruction Manual
Models: HDF1, HDF2, HDF3, and HDF4
GENERAL SAFETY INFORMATION
1. Pressurized devices:
This equipment is a pressure containing device.
• Do not exceed maximum operating pressure as
shown on equipment serial number tag.
• Make sure equipment is depressurized before work-
ing on or disassembling it for servicing.
2. Breathing air:
• Air treated by this equipment may not be suitable
for breathing without further purification. Refer to
OSHA standard 1910.134 for the requirements for
breathing quality air.
1.0 GENERAL DEScRIpTION
Hankison silica gel desiccant dryers are designed
to lower the dew point of compressed air. They
consist of a filter housing filled with silica gel desiccant
through which air passes. As the air passes across
the silica gel desiccant, moisture is adsorbed into
the pores of the silica gel, reducing the moisture
content (dew point) of the outlet air. Once the silica
gel desiccant reaches a level of saturation that causes
the outlet dew point to rise above an acceptable
level, the silica gel desiccant can be either replaced or
regenerated by baking in an oven.
Prefilter
Dryer
SERVICE DEPARTMENT: (724) 746-1100
single tower
desiccant
compressed
air dryer
HdF series
E
N
G
L
I
S
H
E
S
P
A
Ñ
O
L
F
R
A
N
Ç
A
I
S

Publicidad

Tabla de contenido
loading

Resumen de contenidos para SPX Hankison HDF1

  • Página 1 Part No.: 7610.714.18 Catalog No.: 3227469 Rev. A 01/11 Instruction Manual Models: HDF1, HDF2, HDF3, and HDF4 GENERAL SAFETY INFORMATION 1. Pressurized devices: This equipment is a pressure containing device. • Do not exceed maximum operating pressure as shown on equipment serial number tag. •...
  • Página 2 2.0 INSTALLATION Silica Gel Desiccant Life: Table 1 shows the theoretical life of the unit at the stated Location: operating conditions. Life of the silica gel desiccant will The dryer should normally be placed upstream of a re- vary depending on inlet flow, pressure and temperature. ducing valve (regulator).
  • Página 3: Dimensions & Weights

    4.0 MAINTENANcE NOTE: If prefilter unit present, check system at least once per Model HDF1 requires 1 lb of replacement silica gel day to ensure proper drainage. desiccant. Model HDF2 requires 2 lbs of replacement silica gel Changing silica gel desiccant: desiccant.
  • Página 4 CAnonSBURg, PA 15317-1700 U.S.A. Tel | 724 | 745 | 1555 FAX | 724 | 745 | 6040 email: hankison.service@dehydration.spx.com www.hankisonintl.com www.spxft.com © 2011 SPX Corporation. All rights reserved. Improvements and research are continuous at Hankison. Specifications may change without notice.
  • Página 5: Modelos: Hdf1, Hdf2, Hdf3 Y Hdf4

    Part No.: 7610.714.18 Catalog No.: 3227469 Rev. A 01/11 MANUAL DE INSTRUCCIONES MODELOS: HDF1, HDF2, HDF3 y HDF4 INFORMACION GENERAL DE SEGURIDAD 1. DISPOSITIVOS PRESURIZADOS: Este equipo es un dispositivo sujeto a presión. • No exceda la presión máxima de operación que se muestra en la placa del secador.
  • Página 6: Instalacion

    2.0 INSTALACION Vida del Desecante Sílica Gel: La Tabla 1 muestra la vida teórica de la unidad con las Localización: condiciones de operación especificadas. La vida del El secador deberá instalarse normalmente antes de la desecante sílica gel puede variar dependiendo del válvula reductora de presión (regulador).
  • Página 7: Mantenimiento

    4.0 MANTENIMIENTO El modelo HDF1 requiere 1 lb de desecante sílica gel de remplazo. NOTA: Si se cuenta con un prefiltro, verifique el sistema cuan- El modelo HDF2 requiere 2 lb de desecante sílica gel de do menos una vez al día para asegurarse que esté drenando. reemplazo.
  • Página 8: Garantia

    CAnonSBURg, PA 15317-1700 U.S.A. Tel | 724 | 745 | 1555 FAX | 724 | 745 | 6040 email: hankison.service@dehydration.spx.com www.hankisonintl.com www.spxft.com © 2011 SPX Corporation. All rights reserved. Improvements and research are continuous at Hankison. Specifications may change without notice. 4 SP...
  • Página 9: Description Générale

    Part No.: 7610.714.18 Catalog No.: 3227469 Rev. A 01/11 MANUEL D’INSTRUCTIONS Modèles : HDF1, HDF2, HDF3 et HDF4 INFORMATIONS GÉNÉRALES POUR LA SÉCURITÉ 1. DISPOSITIFS SOUS PRESSION: Cet équipement est un dispositif sous pression. • Ne dépassez pas la pression d’exploitation maximale, tel qu’indiqué...
  • Página 10 2.0 INSTALLATION Durée de vie du gel de silice Le tableau 1 présente la durée de fonctionnement Emplacement: théorique de l’appareil dans les conditions de Le séchoir doit être en général placé en amont d’un fonctionnement spécifiées. La durée de vie du gel robinet réducteur de pression (régulateur).
  • Página 11: Dimensions Et Poids

    4.0 ENTRETIEN La quantité de gel de silice sec requise est de 454 g (1 lb) pour le modèle HDF1, REMARQUE : Si le système comporte un préfiltre, vérifier au 907 g (2 lb) pour le modèle HDF2, moins une fois par jour qu’il se vide convenablement. 1814 g (4 lb) pour le modèle HDF3 et 2722 g (6 lb) pour le modèle HDF4.
  • Página 12 AVANT DE RETOURNER LE MATÉRIEL À L’USINE OU D’EFFECTUER DES RÉPARATIONS PENDANT LA PÉRIODE DE GARANTIE, IL FAUT OBTENIR L’AUTORISATION DU SERVICE TECHNIQUE. SERVICE DEPARTMENT: (724) 746-1100 Ç © 2011 SPX Corporation. All rights reserved. Improvements and research are continuous at Hankison. Specifications may change without notice. 4 FR...

Este manual también es adecuado para:

Hankison hdf2Hankison hdf3Hankison hdf4

Tabla de contenido