Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION
We strongly recommend the removal of the
old wall sleeve and the installation of a new
Kenmore folding Wall Sleeve,
If you decide to keep the existing wall sleeve,
you have to redirect the louvers at the back of the
wall sleeve illustration. The use of pliers is
recommended. If you DO NOT redirect, you run
the risk of poor performance or product failure.
This is not covered under the terms of the
Kenmore warranty.
• Pick a location
which will allow the conditioned
air to
blow into the area you want. Good installation
with
special attention
to the proper position of the unit will
lessen the chance
that service will be needed.
NOTE:
All wall sleeves
used to mount
the new Air
Conditioner
must be in sound
structural
condition
and have a rear grille that securely
attaches
to
sleeve,
or rear flange
that serves
as a stop for the
Air Conditioner,
_-'_ Remove
old air conditioner
from existing
wall
sleeve.
_1
Clean the interior
of an existing
sleeve.
(Do not disturb
seals.)
D
Wall
sleeve
must be securely
fastened
in wall
before
installing
the air conditioner.
Use the
nails or screws
through
sleeve
into wall, if
needed.
Repaint
sleeve
if needed.
_4J Prepare
the wall sleeve
for installation
of the
unit. If you plan to use your existing
wall sleeve,
and it is not Kenmore,
use procedure
B or C
below.
ITEMS
IN INSTALLATION
HARDWARE
You may not need all parts in the kit. Discard unused
_arts
Plastic grille
Horizontal insulation Strips
Around
Insulation
Strips
Support
Block
Baffle
Shim
Trim Frame
Washer
Screw
Nuts(Plastic)
Grille
Rear
ITEM
(inches)
263/4 x 161/2
13/8 x 5/8 x 273/18
13/8 x 13/8 x 273/18
13/8 x 3/4 x 611/2
13/8 x 13/8 x 611/2
13/4 x 13/8 x 45/18
14
x 41/2 x 1/8
13x
1 x3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
1
HOW TO INSTALL
D
Identify
the existing
wall sleeve
before
installing
the unit from the listed below.
Brand
Wall Sleeve Dimensions
(inches)
White-Westinghouse
Frigidaire
Carrier
(52F series)
General
Electric
/Hotpoint
Width
25-1/2
26
Whirlpool
25-7/8
Fedders/Emerson
27
Sears/Kenmore
25-7/8
Emerson/Fedders
26-3/4
Carrier
(51S Series)
25-3/4
Friedrich
27
Height
Depth
15-1/4
16, 17-1/2
or 22
15-5/8
16-7/8
17-1/8
16-1/2
or 23
16-3/4
16-3/4
or 19-3/4
15-17/32
16-23/32
15-3/4
15
16-7/8
18-5/8
16-3/4
16-3/4
Procedure
Brand
Depth(inches)
A
Sears/Kenmore
16-23/32
White-Westinghouse
Frigidaire
Carrier
16, 17-1/2
or 22
(52F series)
B
General
Electric
16-7/8
/Hotpoint
Whirlpool
17-1/8 or 23
Carrier
(51S series)
18-5/8
16-3/4
Fedders/Emerson
or 19-3/4
C
Emerson/Fedders
15
Friedrich
16-3/4
Q
Install
new unit into wall sleeve.
CAUTION:
When
installation
is completed,
replacement
unit MUST
have a rearward
slope as
shown.
To achieve
1/4" slope,
remove
the backing
from the 13" shim strips and attach
them
as shown
below
in Fig. 2. Place
the higher
portion
of shim to
the front of the rib on base of wall sleeve.
I
'r
highI [
SHIM PLACEMENT
JI3/4 " High
UNiT
Wall Sleeve
UNIT INSTALLATION
FIG. 2
-6-
Publicidad
Capítulos
Tabla de contenido
