Before You Begin; Transport And Storage - SERVPRO Stealth AV3000 Manual De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

When Franchises purchase equipment from SERVPRO
Industries, Inc., unit date of purchase and serial numbers are
recorded on the invoice. As part of the SERVPRO Industries,
Inc. RMA/Warranty program, proof of purchase and equipment
warranty records are added to the database. This service saves
Franchisees time and resources spent attempting to determine
warranty coverage for equipment.
After receipt of the completed Warranty/RMA Request Form, an
RMA Coordinator will check warranty status on any listed
equipment prior to submitting the claim information to the
vendor(s).
If the unit is covered under warranty, the RMA Coordinator will
communicate the repair and return process.
If equipment is not covered under warranty, the vendor(s) will
provide a competitive repair estimate prior to completing any
non-warranty repairs. The RMA Coordinator will present repair
Fig. B: Disassembly for cleaning
Remove the four screws as shown and lift off the front assembly.
Retain screws for reassembly. Do not overtighten screws.
Fig. C: Stacking for storage or transport
07-02212B F568-SP
options and receive Franchise approval prior to authorizing non-
warranty repairs.
The SERVPRO RMA Department is here to serve you!

BEFORE YOU BEGIN

Warranty registration
Please visit warranty.drieaz.com to register your product.
Registration allows Dri-Eaz to better assist with operation,
maintenance, servicing of equipment, and to contact you in case
there is important safety information concerning your Dri-Eaz
product. If you determine service is required, have your
equipment model, serial number and original proof of purchase
available and call SERVPRO
with obtaining a return material authorization (RMA).
OPERATING INSTRUCTIONS
1.
Unwrap the cord and plug the unit into a standard 115V
GFCI-protected outlet. CAUTION: Be sure switch is in the
off position before connecting unit to power outlet.
2.
For ventilation, direct the Stealth outlet where desired. For
drying, direct the outlet toward the surface to be dried.
Secure the airmover orientation by tightening the knobs on
either side of the unit.
3.
When finished, unplug the unit and re-wrap the cord in the
cord wrap.
Electrical safety devices
Circuit breaker: If the circuit breaker detects overload or short
circuit conditions, the breaker will automatically shut off the
electrical supply. If this should occur, check the power cable
carefully for any damage and ensure it is plugged into a properly
grounded outlet. Press the Circuit Breaker Reset Switch (Fig. A)
to reestablish the electrical supply.

TRANSPORT AND STORAGE

Always use the handle to load or carry the unit.
For cord storage, wrap cord around housing in groove.. Pull cord
snug and secure with plug clip (Fig. A).
Units may be stacked up to five high for transport and storage
(Fig. C). To stack, tip first unit back onto its outlet side and nest
additional units on top (Fig. A).
When transporting, secure the unit(s) carefully to prevent sliding
and damage to the unit and/or injury to vehicle occupants.
Keep unit dry. Do not expose the unit to rain or snow.
MAINTENANCE
WARNING: Unplug unit before performing any maintenance.
Before each use
Inspect the power cord. If cord is damaged, do not use. Always
grasp the plug (not the cord) to unplug.
As needed
Clean housing and impeller. If dust accumulation is visible in the
interior, remove the four screws from the outlet grill as shown
(Fig. B). Clean impeller assembly and all surfaces with
pressurized air and/or with a soft cloth. Do not apply liquids to
the impeller assembly. The housing may be cleaned with a mild
solution of detergent and warm water. Ensure housing is
completely dry before reassembling.
2
®
RMA Department for assistance
Dri-Eaz Products, Inc.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

F568-sp

Tabla de contenido