Installation Instructions - Sharp EBR-47ST Manual Del Usuario

- Utilization of the package will make installation easier.
1. (For U.K., Australian, and New Zealand use)
A cut-out will have to be provided in the right side of the kitchen cabinet for the plug of the oven.
N.B.The mains plug must be accessible after instalation or an all-pole switch disconnection must be
provided with a contact separation of at least 3 mm in each pole.
(For Continental use)
The electric outlet must be installed at 150 mm high from the floor of the built-in cabinet and at 50 mm
from the right wall of the built-in cabinet as shown in Fig. 1. The mains plug must be accessible after
installation or the oven must be connected to an electric circuit provided with an all-pole switch (contact
gap no less than 3 mm) to disconnect the oven in case of danger. A safety-device like a fuse in the
installation may be used as a switch.
2. Remove the built-in kit from the package. Set the package of the built-in kit as it was.
3. Place the oven on the package of the built-in kit as shown in Fig. 3.
Caution: Make sure that the oven always keeps its balance to avoid falling over.
4. Attach the aluminium sheet
And set the spacing brackets
keeping a distance of 17 mm between the front end of the shelf and the spacing brackets, and attach
them with the four screws
Caution: The arrow marks on each spacing bracket should be pointing towards you.
5. Insert two tabs of the intake duct
And install the intake duct
6. Loosen one screw
7. Install the exhaust duct
6) as shown in Fig. 4.
8. Loosen the one screw
9. Remove the one screw
10. Let the power supply cord pass through the hole of the lower side of the intake duct
11. Install the intake duct
at step 9) as shown in Fig. 5.
Caution: Avoid pinching the power supply cord between the oven and the intake duct
12. Remove the backing paper from the three cushions
left side of the intake duct
shown in Figs 6-a and 6-b. Attach the cushion
13. (For U.K., Australian, and New Zealand use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet feeding the power supply cord
through the prepared cut-out.
(For Continental use)
Place the oven on the spacing brackets on the shelf of the kitchen cabinet.
14. Connect the oven to the power supply.
Caution: a. In U.K., Australia, and New Zealand, connect the oven to the power supply 230-240 V, 50 Hz.
b. In the Continent, connect the oven to the power supply 230 V, 50 Hz.
15. Adjust the position of the oven so that the feet of the oven are fitted into the recesses of the spacing
brackets as shown in Fig. 2.
Caution: Make sure that the power supply cord does not touch the air vent openings behind the oven.
16. Place the built-in frame element
horizontally. Secure loosely to the kitchen cabinet with two screws
17. Insert two built-in frame side elements
And secure two screws
and left built-in frame side elements
Note: Fit the hole of the built-in frame side element
18. Install the second built-in frame element
the oven. And secure the built-in frame element
9
to the kitchen cabinet with two screws
Caution: Make sure that the 7.5 mm of the frames (upper and lower) and cabinet overlap each other
as shown in Fig. 9, or the kitchen cabinet door may touch the built-in frame elements.
EBR47ST O/M 2

INSTALLATION INSTRUCTIONS

C
onto the back panel
1
on the shelf along the right and left walls of the kitchen cabinet,
0
, as shown in Fig. 1.
3
into the slits of the back plate
3
to the back plate
F
holding the outer wrap to the rear of the oven as shown in Fig. 4.
2
to the rear of the oven by tightening two screws
G
holding the back plate
H
from the oven as shown in Fig. 4.
4
to the rear of the oven with two screws
4
and attach the cushion
8
on top of the oven making sure that it is level both vertically and
9
between the built-in frame element
B
tightly as shown in Fig. 7. Check location by measuring distance between right
9
. The distance is stated in Fig. 8.
8
over the built-in frame side elements
B
as shown in Fig. 7.
D
of the built in cabinet as shown in Fig. 1 and Fig. 2.
E
.
E
A
with one screw as shown in Fig. 4.
E
to the rear of the oven as shown in Fig. 4.
G
(loosened at step 8) and
5 6 7
, and . Attach the cushion
7
at the left side of the cushion
5
at the top of the oven as shown in Figs 6-a and 6-b.
B
as shown in Fig. 7.
9 B
to the screw when inserting.
8
through the holes of the built-in frame side elements
2
08.3.28, 0:46 PM
2
F
A
and (loosend at step
4
as shown in Fig. 5.
H
(removed
4
.
6
at the top and
6
and the oven as
8
and the kitchen cabinet.
9
at bottom edge of