Publicidad
Idiomas disponibles
Idiomas disponibles
4
Secure the template to the selected location.
5
Using a rotary tool or jigsaw, cut the mounting surface along
the inside of the line on the template.
6
Place the subwoofer in the cutout to test the fit.
7
If necessary, use a file and sandpaper to refine the size of
the cutout.
8
After the subwoofer fits correctly in the cutout, ensure the
mounting holes on the subwoofer line up with the pilot holes
on the template.
9
If the mounting holes on the subwoofer do not line up, mark
the new hole locations.
10
Using an appropriately sized drill bit for the mounting surface
and screw type, drill the holes.
11
Remove the template from the mounting surface.
12
Connect the subwoofer wires
(Subwoofer Wiring, page
13
If necessary, connect the LED wires to the Sports model
subwoofer
(LED Wiring, page
14
Place the subwoofer in the cutout.
15
Secure the subwoofer to the mounting surface using the
included screws
.
NOTE: Do not over tighten the screws, especially if the
mounting surface is not flat.
16
With the subwoofer mounted, hold the grille with the FUSION
logo at the bottom, or at the 6 o'clock position.
17
Press on the grille to snap it into place.
Subwoofer Wiring
When connecting the subwoofer to your amplifier or source,
observe the following considerations.
• Speaker wire is not included with the subwoofer. You should
use 20 AWG (0.52 mm
subwoofer to the amplifier or source.
• The leads on the subwoofer are terminated using male spade
connectors. You should use female spade connectors (not
included) to connect the speaker wire to the speaker leads
for the best connection.
• The subwoofer features a dual 2 Ohm voice coil that can be
configured for 2.1 operation (two speakers and one
subwoofer) when connected to a FUSION stereo with DSP
capability
(Configuring the Subwoofer for 2.1 Operation,
page
4).
• You can use the following table to identify the polarity of the
leads on the speaker.
White
Gray with a black stripe
NOTE: Gray and white with a black stripe wires are
connected to jumper terminals on the back of the subwoofer.
These wires must remain connected to the jumper terminals
for normal use (4 Ohm) and should be disconnected only
when configuring the speaker for 2.1 operation.
Installation Instructions
while observing polarity
3).
3).
2
) speaker wire to connect the
Positive (+)
Negative (-)
LED Wiring
Connecting the LED Wires
You can control the color of the LEDs by connecting the LED
color wires to ground. You can splice the ground wire to multiple
LED wires to customize the LED color.
NOTE: This feature is available only on the sports model.
NOTE: Instead of connecting the LED wires for one dedicated
color, you can install a remote control to turn the LEDs on and
off, change the color, and create lighting effects. See your
FUSION dealer or
www.fusionentertainment.com
information.
The black wire on the LED cable is terminated with a 4 mm
female bullet connector, and the color wires are terminated with
4 mm male bullet connectors. You can connect these to 4 mm
bullet connectors on your wires (not included), or remove the
bullet connectors to connect to the bare wires instead.
1
Connect a positive wire to the black wire on the LED cable.
2
Connect a ground wire to the wire on the LED cable
according to the preferred LED color.
LED Color
LED Wire Color
Red
Red
Green
Green
Blue
Blue
Yellow
Red and green
Magenta
Red and blue
Cyan
Blue and green
White
Red, green, and blue
3
Route the positive and negative wires, and connect them to a
power source
(Connecting the LED Wires to Power,
page
3).
Connecting the LED Wires to Power
NOTE: This feature is available on only the sports model.
You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at
the power-source end of the cable. You should connect the
positive (+) power wire to a 12 Vdc power source through an
isolator switch or circuit breaker to turn the LEDs on and off. You
can use the same isolator or circuit breaker controlling the
power supply to your stereo, which allows you to turn the LEDs
and the stereo on and off at the same time.
You should use 22 AWG (0.33 mm
the LEDs to the battery.
1
Route the positive power (+) and negative ground (-) wires
from the LED-wire connections to the battery.
2
Connect the negative wire to the negative (-) battery terminal.
3
Connect the positive wire to the positive (+) terminal through
a 3 A fuse and isolator switch or circuit breaker.
Subwoofer Sound Optimization
While installing the subwoofer, you can ensure the sound from
the subwoofer is optimized by running the subwoofer out of
phase. You can switch the positive and negative wires on the
amplifier or source to run them out of phase.
Running the subwoofer out of phase from the speakers allows
you to hear if the perception of bass is more from the location of
the subwoofer or from the speakers. If running the subwoofer
out of phase gives a better perception that the bass is from the
speakers' location, then out-of-phase wiring is correct for your
system.
You can run the subwoofer out of phase by temporarily
switching the positive and negative connections from the
subwoofer at the amplifier or source. Depending on the outcome
of the test, you can then switch the connections back if
necessary.
for more
2
) or thicker wire to connect
3
Publicidad
