Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT: Trims must be grounded
as outlined below. Failure to do
so can result in electric shock or
undesired operation.
4RLD
The 4RLD trim is retained by push in friction
springs which flex into the side walls of the
housing. The sidewalls of the housing must be
grounded to provide electrical ground to the
trim (see Fig. 2).
5RLD & 6RLD
The recessed housing must contain grounded
brackets to support the trim springs and
provide electrical ground to the trim (see
Fig. 3). If the housing is grounded but does
not contain spring retaining brackets, contact
factory to order an adapter kit (V6RL-TRB).
Figure 2
Recessed
Typical Spring
Housing
Retaining Bracket
Figure 3
To use any of these products in an
ungrounded housing, consult factory for
additional instructions.
WARRANTY
5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Technical Services Phone (888) 387-2212
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/juno-recessed
©2017 Acuity Brands Lighting, Inc
INSTALLATION INSTRUCTIONS
For 4RLD, 5RLD & 6RLD Retrofit Trim Series
Dedicated Quick Connect Housings
As standard, the primary connection means
provided on the Juno retrofit trims is a
connector that is designed to meet the high
efficiency requirements of California T24.The
connector is only intended to be plugged into
the mating connector in Juno housings
(Refer to chart below) or into the medium
base Socket adaptor (if provided with the
trim). Use of this trim in any other quick
connect housings other than Juno or
removing the factory installed connector is
prohibited and voids the product warranty.
Retrofit Trim
4RLD
5RLD
6RLD
IMPORTANT: Power to the luminaire
must be turned off prior to installing
Housing
these LED trims. Failure to do so
Side Wall
can cause electric shock, which can
result in injury or death.
Installation
Step 1. Confirm the LED trim is compatible
with the recessed housing as outlined
previously in these instructions.
Friction
Step 2. Some recessed housings contain an
Springs
adjustable plate or bracket that supports the
socket. The socket may need to be detached
from the plate/bracket, and the plate/bracket
may need to be removed from the housing
prior to installation of the trim. For detailed
instructions on removing the plate or bracket,
refer to manufacturer's installation instructions.
If the housing has been modified, the
luminaire label provided loose with this retrofit
kit must be affixed to the luminaire in a
location visible after installation and during
relamping.
Step 3. Installation into existing housings with
medium base sockets: Screw the medium
base socket adaptor into the socket in the
recessed housing. Plug the connector
provided on the trim to the mating connector
on the socket adaptor by pushing firmly to
ensure connectors are securely fastened (see
Fig. 4).
Installation into dedicated quick connect
housings: Plug the connector provided on the
trim into the mating connector in the housing
by pushing firmly to ensure connectors are
securely fastened (see Fig. 5).
Rev 2/19
Quick Connect Housings
IC1 LEDT24, IC1R LEDT24, IC1JB
IC20 LEDT24, IC20R LEDT24
IC23 LEDT24, IC23R LEDT24
P6170
Step 4. 4RLD: Insert trim into housing using
push in friction springs. Carefully push trim
towards ceiling until fully installed with trim ring
flush to the ceiling.
5RLD & 6RLD: Insert trim torsion springs
into corresponding retaining brackets in
recessed housing. Carefully push trim towards
ceiling until the springs pull the trim flush to
the ceiling.
** Make certain wires are not pinched
or damaged during installation.
Step 5. Turn power on to fixture.
Incandescent
Housing
Figure 4
Dedicated Quick
Connect Housing
Quick Connect
Figure 5
Medium Base
Socket Adapter
Quick Connect
2 of 2
Publicidad
