Porter & Cable PCE210 Manual De Instrucciones página 4

Llave de impacto con yunque de anillo del cerdo de 13mm (1/2 pul)
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

WaRNiNG:
ALWAYS use safety
glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust mask
if drilling operation is dusty. ALWAYS
WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87 .1 eye protection (CAN/
CPA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NOSH/OSHA respiratory protection.
WaRNiNG:
always wear proper
personal hearing protection that
conforms to aNSi S12.6 (S3.19) during
use. Under some conditions and duration
of use, noise from this product may
contribute to hearing loss.
WaRNiNG:
Some dust created by
power sanding, sawing, grinding, drilling, and
other construction activities contains
chemicals known to the state of California to
cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
microscopic particles.
• avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into
your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WaRNiNG:
Use of this tool can
generate and/or disperse dust, which may
cause serious and permanent respiratory
or other injury. Always use NOSH/OSHA
approved respiratory protection
appropriate for the dust exposure. Direct
particles away from face and body.
Symbols
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
or AC ......alternating current
or DC ...direct current
n o ................no load speed
................Class I Construction
................earthing terminal
(grounded)
...............safety alert symbol
................Class II Construction
(double insulated)
.../min or rpm...revolutions or
..............Read instruction manual
before use
................Use proper respiratory
protection
...............Use proper eye protection
................Use proper hearing
protection
BPM ...........beats per minute
• When using an extension cord, be sure to
use one heavy enough to carry the current
your product will draw. An undersized cord
will cause a drop in line voltage resulting
in loss of power and overheating. The
following table shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the
gauge number, the heavier the cord.
Minimum Gauge for cord Sets
Volts
120V
0-25
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V
0-50
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
ampere Rating
More
Not more
Than
Than
0
-
6
18
6
-
10
18
10 -
12
16
12
- 16
14
4
reciprocation per minute
total length of cord in feet
26-50
51-100
51-100
101-200 201-300
American Wire Gauge
16
16
16
14
16
14
12
Not Recommended
101-150
14
12
12

Publicidad

Tabla de contenido
loading

Tabla de contenido