Force And Timer To Close; Program Limits - Chamberlain LiftMaster Professional CB24 Manual De Instrucciones

FORCE AND TIMER TO CLOSE

FORCE CONTROL
Set the sensitivity such that the unit will
complete a full cycle of gate travel but will
reverse off an obstruction without applying
an unreasonable amount of force.
MIN MAX
INSTALL ALL EQUIPMENT IN COMPLIANCE WITH EN60335-2-103, EN13241-1.

PROGRAM LIMITS

1. Turn BiPart switch to desired setting. Set to "Off" for single
gate applications.
2. Press the "LEARN LIMITS" button.
3. The "SET OPEN LIMIT" LED will blink.
4. Use any of the "Gate 1" buttons to move Gate 1 to the
desired open position. Repeat if Gate 2 is present using "Gate
2" buttons.
5. Press the "LEARN LIMITS" button to set the Open Limit for
gate(s).
6. The "SET OPEN LIMIT" LED will turn off. The "SET CLOSE
LIMIT" LED will blink.
7. Use the "Gate 1" buttons to move Gate 1 to the desired close
position. Repeat if Gate 2 is present using "Gate 2" buttons.
8. Press the "LEARN LIMITS" button to set the close limit for
gate(s).
9. The "SET CLOSE LIMIT" LED will turn off. The limits are set.
10 Using programmed remote or single button input (SBC) run
the gate(s) from the close limit to the open limit. After
reaching the open limit, run the gate(s) to the close limit.
This will learn the force in the open and close direction.
11. If the learned force is not high enough, manually
adjust the force control as described above.
The "Save" Dip switch must be set to OFF to allow programming.
After completion set the "Save" switch back to on.
NOTE: Any following SBC or Remote inputs will move the gate .
BIPART DELAY
Set the BIPART DELAY to desired
setting. The range is 0 to 8
seconds, 0 seconds is OFF.
OFF MAX
ALARM
NO
C
MAGLOCK
NO
C
NC
Z1
GATE 1
BRN
GRN
WHT
YEL
BLU
RED
Z12
ACCESSORY
POWER
24V
BRN
GRN
WHT
YEL
BLU
RED
GATE 2
D15
R4 C2
24 VAC/
SOLAR
INPUT
J4
SET
OPEN
LIMIT
14
TIMER TO CLOSE ENABLE
Set the TIMER TO CLOSE to
desired setting. The range is 0 to
180 seconds, 0 seconds is OFF.
OFF
P2
J19
K6 Ø14GPØ89ØE
Ø14LGØ89ØE
Ø14SKØ89ØE
K5
L1
1
OFF ON SAVE
R2
OFF ON MAGLOCK
LEARN SINGLE DUAL MODE
XMITTER
R1 NO NC EDGE
10A 32V
NO NC PHOTO
2
S1
F3
D1Ø K2
DIAGNOSTIC
GATE 1
SET SET
LEARN
K1
Q9
OPEN CLOSE
LIMITS
LIMIT LIMIT
TIMER
R9Ø
GATE 2
RUNNING
BIPART TIMER TO
DELAY
FORCE
R1Ø1
R1ØØ
F4
ACCESSORY
10A 32V
OVLD
K4
MIN MAX OFF MAX OFF
F5
D21
R35
K3 D9
D8 C12
D27 Z3
Z4
D22
Q22
U3
C11
R196
MOV2
R9 D4
MOV1
D1
C64
JMPR2 JMPR1
U2 D2
DB1
DIAGNOSTIC
SET
CLOSE
LIMIT
FORCE
MAX
R223
CLOSE
EDGE
R2Ø7
Z2Ø
R227
OPEN EDGE/
PHOTO
J18
R224
Z22
U4
R92
Z9
OPEN
PHOTO
R91
R94
Z8
CLOSE
PHOTO
R93
24V
SWITCHED
ACCESSORY
COM OVLD
POWER
OVLD
CONTROL
SINGLE
INPUTS
CLOSE BUTTON
OPEN
SINGLE BUTTON
RESET
STOP
MAX
COM
COM
POWER
F7
LOOP
INPUTS
C13
C4
SHADOW
INTERRUPT
CHGR COM
OVLD
F6
F2
F1 20A 32V
FUSE
BATT 2 BATT 1
OPEN
GATE 1
LEARN
LIMITS
GATE 2