Setting The Timer - DVA GIX Serie Manual De Instrucciones

GIX
instruction
manual
it is filled.
Proceed with settings.

5) SETTING THE TIMER

NOTES ON SETTING PROCEDURE
If no button is pressed for longer than 20 seconds during the
setting procedure, the display will go back to showing the
current time.
5.1 GIX SERIES (COMMANDS DESCRIPTION)
The GIX timer has four buttons and a display. They will allow
you to set up the parameters to let the equipment work cor-
rectly (fig. 9).
In working mode, the display shows the time, the day, and the
days for scheduled regenerations.
During regeneration, it shows the remaining time until com-
pletion and which phase it is currently performing (fig. 18).
5.2 TURNING ON THE EQUIPMENT
Plug in the equipment and connect the connector to the timer
(fig. 6, G). The display (fig. 9, E) will show the time.
If "ERR3" appears instead, wait for the valve to position itself
correctly. The error message will disappear and the time will
appear on the display.
5.3 SETTING THE DAY AND TIME
1. Press N . The display will flash.
ih
2. Using the buttons, set the current time (fig. 10).
3. Press N to confirm.
A small triangle indicating the day will appear on the higher
part of the display (fig. 11).
1. Press N to make the small triangle flash.
ih
2. Using the buttons to the current day (fig. 12).
3. Press N to confirm.
5.4 SETTING THE REGENERATION TIME
On the left side of the display, a amall triangle will point to the
words ("Regen time").
1. Press N . The display will flash.
ih
2. Using the buttons, select the regeneration time (fig.
13).
3. Press N to confirm.
16
CRONOMETER
fig.10
fig.11
fig.12
fig.13
5.5 SETTING THE REGENERATION DAY
On the display, you will see a number indicating the number
of days elapsing between regenerations, and a little triangle
under the word DAYS (fig. 14).
1. Press N . The display will flash.
ih
2. Press the uttons to choose the number of days elap-
sing between a regeneration and the next. Values go from
0.5 to 99.
The 0.5 value means that two regenerations a day will be
performed, one every 12 hours. For example: if "regene-
ration time" (see paragraph 5.4) is set at 17, the following
regeneration will be performed at 5 a.m.
The other values go from 1 (one regeneration a day) to 99
(one regeneration every 99 days). Press N to confirm.
If, instead, you wish to select specific days of the week for the
regeneration to be performed, use the buttons
value 0 and press N.
1. The 0 value will disappear from the display, and a small
triangle on the left side will point to the words "regen day".
2. Press N. Another small triangle will flash in the higher part
of the display, right under the SU day (Sunday).
3. Press N. The small triangle will move to the following day,
without flashing.
4. It is now possible, using the
right to the regeneration days of your choice.
5. Press N and the small triangle will flash.
h
6. Press to confirm, and the chosen day will be underlined.
The regeneration will take place on the underlined days
(fig. 15).
7. Press N to confirm.
8. Set the regeneration days of your choice.
9. Press and hold N until a letter appears on the display (fig.
16).
5.6 SALT DOSAGE FOR REGENERATION
fig. 16
The value "salt amount" determines the duration of the rege-
neration and the necessary salt dose.
The value is set by the manufacturer and must be modified
under supervision of the installer.
1. After setting the regeneration days, a letter ("S", "L" or "H")
will appear on the display.
2. Press N The display will flash.
3. Select the L letter using the
4. Press N to confirm.
End of settings.
5.7 LOCKING THE SETTINGS
To prevent any unwanted modification of the settings, it is
Instruction Manual GIX CRONOMETER
ENGLISH
fig.14
ih
to set the
fig.15
ih
buttons, to move left and
fig. 17
ih
buttons (fig. 17).