Introduction; Device Description; Scope Of Delivery; Intended Use - Parkside PDM 600 A1 Instrucciones De Utilización Y De Seguridad

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
we hope your new tool brings you much enjoyment and suc-
cess.
Note:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling
• Non-compliance of the operating instructions
• Repairs by third parties, not by authorized service techni-
cians
• Installation and replacement of non-original spare parts
• Application other than specified
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers.
In addition to the safety notes contained in the present oper-
ating instructions and the special regulations of your country,
the generally recognized technical rules for the operation of
woodworking machines must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
36 GB/MT

3. Device description

1. Motor unit
2. On/Off switch
3. Speed control
4. Headstock drive centre
5. Tool support
6. Tool rest
7. Centering pin
8. Counternut
9. Tailstock
10. Handwheel
11. Clamping lever tailstock
12. Machine bed
13. Locking screw
14. Clamping lever tool rest
15. Face plate

4. Scope of delivery

• 1 Motor unit
• 1 Headstock drive centre
• 1 Tool rest
• 1 Tool support
• 1 Centering pin
• 1 Tailstock
• 1 Machine bed
• 1 Face plate
• 2 Wrench SW24
• 1 Wood turning chisel, flat/angular
• 1 Wood turning chisel, hollow
• 1 Clamping lever tool rest
• 8 Fastening screws (B)
• 1 Instruction manual

5. Intended use

The machine is only designed for working on wood using a
suitable turning tool.
The machine meets the currently valid EU machine directive.
The manufacturer's safety, operation and maintenance instruc-
tions as well as the technical data given in the calibrations and
dimensions must be adhered to.
Relevant accident prevention regulations and other generally
recognized safety and technical rules must also be adhered to.
The machine may only be used, maintained or repaired by
trained persons who are familiar with the machine and have
been informed about the dangers. Unauthorized modifications
of the machine exclude a liability of the manufacturer for dam-
ages resulting from the modifications.
The machine is intended for use only with original spare parts
and original tools from the producer.
Any other use is considered to be not intended. The manufac-
turer excludes any liability for resulting damages, the risk is ex-
clusively borne by the user.
m Please note that our equipment has not been designed for
use in commercial, trade or industrial applications. Our war-
ranty will be voided if the equipment is used in commercial,
trade or industrial businesses or for equivalent purposes.