DSC NEO PowerSeries HSM2208 v1.0 Instrucciones De Instalación

HSM2208 v1.0 Installation Instructions
8 Low Current Output Module
This installation sheet shall be used in conjunction with the Installation Manual of the DSC equipment to
which the HSM2208 is connected (e.g. alarm controller, power supply, etc.).
The HSM2208 module can be used to add up to 8 low-current programmable outputs to the compatible
DSC alarm control panel (alarm panel) models HS2016, HS2032, HS2064 and HS2128.
Specifications
• Temperature range: -10°C to + 55°C (0°C to +49°C for UL/ULC listed systems)
• Relative Humidity: 93% non condensing
• Input ratings: 10.8 to 12.5V /700mA (includes 250mA AUX maximum plus 50mA for each of the 8 out-
DC
puts). The maximum loading is shared with the compatible alarm panel or power supply AUX output.
• Board current draw: 60mA (set and unset state/alarm and non-alarm state)
• Board dimensions: 45mm x 92mm
• AUX output ratings: 10.8 to 12.5V , -15%/ +15% when Input voltage is between 85% to110% of rated
DC
value and output current is between 0mA - 250mA max.
• PGM outputs: Open collector, switched to ground, 50mA max
• Resettable fuse (PTC) used on circuit board instead of replaceable fuses. There are no serviceable parts
• Maximum wire length from alarm panel: 1,000'/305m
Terminal Descriptions
TMP - This can be used to tamper the cabinet in which the HSM2208 is mounted. Connect a normally
closed (NC) switch across TAM and BLK. If the tamper is not being used connect a piece of wire across
TAM and BLK to remove the trouble condition.
NOTE: Tamper protect is required for UL/ULC commercial/residential burglary installations.
NOTE: There is a built-in tamper switch on the expander module located in the top left corner of the cir-
cuit board. If the cabinet in which the HSM2208 is mounted has the hardware required to depress this
tamper switch, do not connect anything to the TAM terminal.
+AUX+ - There are two terminals for AUX power to provide easier wiring. These terminals are used to
provide power for devices. Maximum current draw is not to exceed 250 mA. Connect the positive lead of
powered devices to either AUX+ and the negative to the proper output terminal (O1 to O8).
CORBUS
- The 4-wire Corbus connection is used by the panel to communicate with the module. Connect
the RED, BLK, YEL and GRN terminals to the Corbus terminals on the main control.
SERIAL NUMBER
SWITCH
LED
To TAMPER SWITCH
or connect to BLK
terminal if TAMPER
SWITCH is not used
CORBUS to
preceding
expansion
module or
alarm panel
O1 to O8 - Wire the positive lead of the device to either AUX terminal and the negative lead to the
required output terminal (O1 to O8). The following are examples of how to wire various devices to the
outputs:
Enclosures
The HSM2208 may be installed within the same metallic cabinet as the alarm controller/power supply
(model Power UC1, PC5003C) or in a separate enclosure (model PC4003C). Internal and/or external wir-
ing for this module shall be routed, supported, clamped or secured in a manner that reduces the likelihood
of: excessive strain on wire and on terminal connections; loosening of terminal connections; and damage
of conductor insulation.
The HSM2208 can be installed in the metal enclosures listed below. Tamper protection switches can be
installed on all enclosures, including door opening protection and/or removal from the mounting position.
Doors can be secured using screws or keylock.
• Model PC5003C (removable door)
• Model PC5003C (hinged door)
• Model Power UC1
• Model PC4003C
• Model CMC-1
• Model PC4050CAR (commercial burglary)
• Model PC4050CR (ULC--S559)
NOTE: Use PC4003C, PC5003C, CMC-1, PC4050CAR, or PC4050CR for UL/ULC installations
NOTE: The Model HSM2208 Output Module has been certified by Telefication according to EN50131-
1:2006 + A1:2009 for Grade 2, Class II when installed in the PC5003C (removable door) enclosure.
Automatically Enrolling on the Alarm Panel
To enroll the HSM2208 follow these steps:
1. Ensure that the system is not powered.
2. Connect the HSM2208 to the Corbus.
3. Power up the system.
4. Enter section [902] [000]and wait 1 minute.
5. Enter section [903] [003]to verify that the module is supervised.
Manually Enrolling on the Alarm Panel
To enroll the HSM2208 follow these steps:
1. Ensure that the system is not powered.
2. Connect the HSM2208 to the Corbus.
3. Power up the system.
4. Enter section [902] [001].
5. Enter the module serial number.
CORBUS to
6. Enter section [903] [003]to verify that the module is supervised.
additional
expansion
Status LED
modules
The HSM2208 is equipped with a status LED to indicate the current status of the module. If the
HSM2208 is operating correctly, the status LED will flash briefly every 10 seconds. When a trouble con-
dition is present, the status LED will display a series of flashes then remain blank for 1.7 seconds. The
number of flashes between blank periods indicates the trouble condition present as outlined in the table
below .
Number of Flashes Trouble Condition
1 Module not enrolled
2 Alarm Panel supervision trouble
3 Corbus low voltage
2 9 0 0 8 4 5 8R0 0 1
LIMITED WARRANTY
Digital Security Controls (DSC) warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use and that in fulfilment
of any breach of such warranty, DSC shall, at its option, repair or replace the defective equipment upon return of the equipment to its factory. This warranty applies only to defects in parts and workmanship
and not to damage incurred in shipping or handling, or damage due to causes beyond the control of DSC such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of
abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of
DSC. This warranty contains the entire warranty. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this war-
ranty, nor to assume for it any other warranty or liability concerning this product. In no event shall DSC be liable for any direct or indirect or consequential damages, loss of anticipated profits, loss of time or
any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to,
criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.
IMPORTANT - READ CAREFULLY: DSC SOFTWARE PURCHASED WITH OR WITHOUT PRODUCTS AND COMPONENTS IS COPYRIGHTED AND IS PURCHASED UNDER THE FOLLOWING
LICENSE TERMS:
This End-User License Agreement ("EULA") is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division
of Tyco Safety Products Canada Ltd. ("DSC"), the manufacturer of the integrated security systems and the developer of the software and any related products or components ("HARDWARE") which You
acquired. If the DSC software product ("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or
install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and "online" or electronic documentation. Any software pro-
vided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a
modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation, terminal or other
digital electronic device ("Device"). In other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given time. You may use the back-up copy solely for archival
purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activ-
ity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not
remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the
SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the SOFT-
WARE PRODUCT (including all component parts, the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is
an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFT-
WARE PRODUCT and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the
accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title
and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable
copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the
arbitrator's decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE "AS IS" WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF
THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the
SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT,
DSC'S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PROD-
UCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES,
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED
(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO
OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT
ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED
UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS,
LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHAS-
ERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that the entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.
The term IC before the radio certification number signifies that the Industry Canada technical specifications were met. This Class B digital apparatus complies with Canadian ICES-003. This device complies
with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Ce dispositif satisfait aux exigences d'Industrie Canada, prescrites dans
le document CNR-210. son utilisation est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by DSC could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer's instructions, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart "B" of Part 15 of FCC Rules, which are designed to provide reason-
able protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to
television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC useful: "How to Identify
and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
The Model HSM2208 Output Module has been certified by Telefication according to
• EN50131-1:2006 + A1:2009 for Grade 2, Class II when installed in the PC5003C (removable door) enclosure.
• EN50131-3:2009 Type A Standard.
© 2014 Tyco International Ltd. and its Respective Companies. All Rights Reserved.
Tech. Support: 1-800-387-3630 (Canada & U.S.), 905-760-3000
Toronto, Canada • www.dsc.com