Tabla de contenido
Publicidad
BASIC SHREDDING OPERATION
Continuous operation: 5 minutes maximum
NOTE: Shredder runs briefly after each pass
to clear entry. Continuous operation beyond 5
minutes will trigger 30-minute cool down period.
ADVANCED PRODUCT FEATURES
SAFESENSE
®
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
D S - 1 2 0 0 C
D S - 1 2 0 0 C
1
2
12
Touch test area and
Turn the shredder ON
look for the SafeSense
( I) to activate
indicator to illuminate
SafeSense
®
BASIC PRODUCT MAINTENANCE
OILING SHREDDER
D S - 1 2 0 0 C
All cross-cut shredders require oil for peak performance.
If not oiled, a machine may experience diminished sheet
capacity, intrusive noise when shredding and could ultimately
12
stop running. To avoid these problems, we recommend you
oil your shredder each time you empty your waste bin.
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
TROUBLESHOOTING
A
B
PAPER JAM
1
2
Set to Reverse (R)
for 2-3 seconds
D S - 1 2 0 0 C
D S - 1 2 0 0 C
PAPER/CARD
1
Plug in and put disconnect
power switch in
ON ( ) position
www.fellowes.com features an extensive on-line support section with a number of self-service options
D S - 1 2 0 0 C
TECHNOLOGY OPERATION
D S - 1 2 0 0 C
D S - 1 2 0 0 C
3
12
12
12
SafeSense
is active
®
and working properly
®
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
D S - 1 2 0 0 C
D S - 1 2 0 0 C
D S - 1 2 0 0 C
12
12
A. Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating
temperature and needs to cool down. This indicator will remain illuminated and the shredder will not operate for the duration of
the recovery time. See Basic Shredding Operation for more information about the continuous operation and recovery time for
this shredder.
B. SafeSense
Indicator: If hands are too close to the paper entry, the SafeSense
®
stop shredding.
3
Alternate slowly back and forth
D S - 1 2 0 0 C
D S - 1 2 0 0 C
D S - 1 2 0 0 C
D S - 1 2 0 0 C
2
Set to Auto On (I)
D S - 1 2 0 0 C
12
12
D S - 1 2 0 0 C
D S - 1 2 0 0 C
12
2
1
Set to Off (0)
*Apply oil across entry
D S - 1 2 0 0 C
15
12
12
4
5
Set to Off (O)
and unplug
D S - 1 2 0 0 C
D S - 1 2 0 0 C
3
4
Feed paper/card
When finished
straight into paper
shredding set to
entry and release
OFF (O)
D S - 1 2 0 0 C
12
12
3
Set to Reverse (R)
2-3 seconds
D S - 1 2 0 0 C
D S - 1 2 0 0 C
D S - 1 2 0 0 C
12
12
12
indicator will illuminate and the shredder will
®
6
Gently pull uncut
Set to Reverse (R)
paper from paper
entry. Plug in.
D S - 1 2 0 0 C
D S - 1 2 0 0 C
12
D S - 1 2 0 0 C
12
3
D S - 1 2 0 0 C
Publicidad
Tabla de contenido
